Pitney Bowes Relay 5000 Скачать руководство пользователя страница 141

Страница: 141 / 202

SV63136 Rev. A

7-9

Add-On Modules • 7

The Flats Sealer also contains an envelope edge marker. The envelope

edge marker will apply a mark at least 0.5" (12.5 mm) in length along the

edge of the envelope facing the operator.
You can use edge mark can be used to indicate tray breaks, ZIP breaks,

every 50th envelope, high value checks, etc.

NOTE:

The envelope edge mark is applied only to envelopes passing through the

letter exit path.

Replacing the

Envelope Edge

Marker Roller

Follow the steps below to remove and replace the Envelope Edge Marker

Roller.

NOTE:

Avoid touching the ink roller, as it is covered in ink.

1.  Open the Flats Sealer cover.
2.  Grasp the tab at the top of the old ink roller and lift to remove.
3.  Grasp the tab at the top of the new ink roller and slide it onto the spin-

dle.

4. Release the tab once the ink roller is seated firmly in place.
5. Close the Flats Sealer cover.

Figure 7.9: Flats Sealer Cover Open

Envelope Edge Marker Roller

Flat Envelope Exit

Letter Envelope Exit

Содержание Relay 5000










































































































































































































Результаты поиска

Содержание Relay 5000

Отзывы:

Pitney Bowes Relay 5000, Руководство оператора, Страница: 141 / 202

Результаты поиска

Содержание Relay 5000

Отзывы: