Pitney Bowes Relay 5000 Скачать руководство пользователя страница 156

Страница: 156 / 202

8-10

SV63136 Rev. A

8 • Scanning

Scanning

Features

(continued)

Divert Sheet Functionality

Divert sheet functionality allows you to create scanning jobs that will send

sheets to the lower divert area if sets exceed a given sheet count or contain

a specific scan mark.
This feature is implemented in one of two ways
• Using the Divert Sheets (DVS) scan mark. The Divert Sheet scan mark

is available on systems that have BCR scanning or the Selective Op-

erations level of OMR scanning enabled. Refer to

BCR and OMR Mark

Levels

in this chapter for more information about the various levels of

scanning.

• Setting the “Item Overcount Action” to “Divert”. Refer to

Creating a Job

Chapter 3

Assigning a Scan Configuration to an Existing Job

in this

chapter for more information.

Jobs using the divert sheet functionality will send diverted sets to the lower

divert area. The remaining parts of the mail piece will be processed, inserted

into an outer envelope, and sent to the upper divert area.

NOTE: If the mail piece contains only a single set, which has been diverted, an

empty envelope will be sent to the upper divert area.

Currently, the system can divert up to 25 sheets. If a set contains more

than 25 sheets, the system will stop and you will need to manually remove

sheets from the Pre-fold Accumulator and the remainder of the set from the

appropriate sheet tray.
Divert sheet functionality cannot function with dynamic envelope selection at

this time.

Lower

Divert Area

Upper

Divert Area

Содержание Relay 5000










































































































































































































Результаты поиска

Содержание Relay 5000

Отзывы:

Pitney Bowes Relay 5000, Руководство оператора, Страница: 156 / 202

Результаты поиска

Содержание Relay 5000

Отзывы: