Pitney Bowes Relay 5000 Скачать руководство пользователя страница 173

Страница: 173 / 202

SV63136 Rev. A

8-27

Scanning • 8

8. Use the blue thumbwheel to move the scan head. Move the thumbwheel

until the pointer lines up with the measurement (distance from the center

of the page to the center of the mark) defined earlier.

Blue thumbwheel

Figure 8.1: Use the Blue Thumbwheel to

Adjust Scan Head Position

NOTE: The scanning area on your system may appear different, but operation

concepts are the same.

NOTE: The scanning area on your system may appear different, but operation

concepts are the same.

9. If additional scan heads are to be used, repeat step 1 to 8 for each.
10. To verify the adjustment is correct:

a. From the home screen, select

Loading Instructions and Pre-Run

Adjustments>canner Setup

b. Use the UP/DOWN arrow keys to select a feeder to run.
c. Press

TRIAL PIECE

to feed a piece from the highlighted feeder.

d. Select

Finish

when done.

Adjusting the

Scan Heads

for Ladder or

2D Orientation

Marks

(continued)

Figure 8.2: Use the Pointer to Ensure Correct

Scan Head Position

Move thumbwheel until pointer lines up

with the distance measured in Step 4.

Содержание Relay 5000










































































































































































































Результаты поиска

Содержание Relay 5000

Отзывы:

Pitney Bowes Relay 5000, Руководство оператора, Страница: 173 / 202

Результаты поиска

Содержание Relay 5000

Отзывы: