Pitney Bowes Relay 5000 Скачать руководство пользователя страница 123

Страница: 123 / 202

SV63136 Rev. A

6-5

Specifications • 6

Capacities
Tower Sheet/

Insert/Envelope

Feeders

•

350 20 lb. (80 gsm) sheets; 350 insert cards; 250 envelopes.

•

Feeders are multi-purpose: they can handle sheets, cards, slips

and envelopes.

•

Feeders, including envelope feeders, can be linked to increase

running time.

•

Feeders are available in pairs of two (maximum four feeders).

Folder

Up to 8 sheets of 20 lb. (80 gsm) material.

Accumulator

Maximum collation thickness is 1/4" (6 mm).

High Capacity

Sheet Feeder

(HCSF)

Available in pairs. Capacity is 2,000 sheets per pair.

Drop Stacker

130 pieces, letter mail; 25 pieces, flat mail.

Vertical Power

Stacker

250 pieces, letter mail (assumes single sheet insert).

Production

Power Stacker

At least one USPS mail tray (two feet of finished mail).

Moistener/

Closer/Sealer

8,000 letters before refilling.

Component

Specifications

Folder
Fold Types

Top address

documents

C fold, Z fold, single

and double fold

Maximum number of

sheets per collation: 8

(20 lb. [80 gsm])

Bottom address

documents

(see Notes below)

C fold, Z fold and

single fold

Middle address

documents

(see Notes below)

C fold

Machine

Adjustments

None

No-Fold (Bypass)

Yes

Notes

•

Documents with addresses on the bottom

may

require the

Inverter kit.

•

Documents with an address present on the middle of the sheet

always

require the Inverter kit.

•

Refer to the

Available

Fold Type/Address Location/

Envelope Type Combinations

table in this chapter for more

information.

Содержание Relay 5000










































































































































































































Результаты поиска

Содержание Relay 5000

Отзывы:

Pitney Bowes Relay 5000, Руководство оператора, Страница: 123 / 202

Результаты поиска

Содержание Relay 5000

Отзывы: