Pitney Bowes Relay 5000 Скачать руководство пользователя страница 61

Страница: 61 / 202

SV63136 Rev. A

3-17

Basic Operation • 3

Loading

the HCEF

(continued)

Figure 3.8.1: Push up on the Separator Gap Lever

Figure 3.8.2: Separator, Raised.

Adjusting the HCEF Separator Gap

NOTE:

You must adjust the HCEF Wedge before you can adjust the Separator

Gap. Refer to

Adjusting the HCEF Wedge

in this chapter for more information.

1. Prepare an envelope for the separator gap adjustment:

a. Cut a strip of 20 lb. (80 gsm) paper to fit inside an envelope.
b. Insert the strip of paper into the envelope.

NOTE:

Tap the envelope lightly against a hard surface to ensure the strip

of paper rests all the way down at the bottom of the envelope.

c. Close the envelope flap.

2. Push up on the separator gap lever to raise the separator.

Содержание Relay 5000










































































































































































































Результаты поиска

Содержание Relay 5000

Отзывы:

Pitney Bowes Relay 5000, Руководство оператора, Страница: 61 / 202

Результаты поиска

Содержание Relay 5000

Отзывы: