Pitney Bowes Relay 5000 Скачать руководство пользователя страница 140

Страница: 140 / 202

7-8

SV63136 Rev. A

7 • Add-On Modules

Flats Sealer

The Flats Sealer add-on module attaches to the exit end of the base module

to allow for the sealing of flat envelopes. The Flats Sealer can seal flat enve-

lopes up to 0.25" (6.5 mm) in thickness.
In the Moistener, Closer, Sealer module, brushes sweep across the flat

envelope flap to wet the glued area of the flap. The Flats Sealer closes the

flap, seals the envelope, and sends it on to the next module downstream.

While the Flats Sealer is designed specifically to seal flat envelopes, it has

an exit path for (sealed) letter envelopes exiting the Moistener, Sealer, Clos-

er module.

Flats Sealer Downstream Attachments

Letter Exit Path

•

Drop Stacker (Letter Mail)

•

Vertical Power Stacker

• Belt Stacker
•

Exit Transport/Mail Machine Interface/Mailing Machine

Flats Exit Path

•

Drop Stacker (Flat Mail)

•

Belt Stacker

•

Exit Transport

Figure 7.8: Flats Sealer Module (shown here with an HCEF)

Flast SealerCover

Содержание Relay 5000










































































































































































































Результаты поиска

Содержание Relay 5000

Отзывы:

Pitney Bowes Relay 5000, Руководство оператора, Страница: 140 / 202

Результаты поиска

Содержание Relay 5000

Отзывы: