Pitney Bowes Relay 5000 Скачать руководство пользователя страница 175

Страница: 175 / 202

SV63136 Rev. A

8-29

Scanning • 8

Figure 8.4: Use the Pointer to Ensure Correct

Scan Head Position

Move thumbwheel until pointer lines up

with the distance measured in Step 4.

7. Determine the direction the Scan Head needs to be moved (to the left or

right of 0 on the ruler):
• Make sure the center of the sheet (the vertical fold) is lined up with

the at the center of the machine (at 0 on the ruler.)

• If the sheet is loaded top first, make sure the arrows point DOWN.
• If the sheet is loaded bottom first, make sure the arrows point UP.

8. Use the blue thumbwheel to move the scan head.

Blue thumbwheel

Figure 8.3: Use the Blue Thumbwheel to

Adjust Scan Head Position

Move the thumbwheel

until the pointer lines up

with the measurement

(distance from the

center of the page to

the center of the mark)

defined in step #7.

9. If additional scan heads

are to be used, repeat

step #1 to 8 for each.

10. To verify the adjustment is correct:

a. From the home screen, select

Loading Instructions>Pre-Run

Adjustments>Scanner Setup

b. Use the UP/DOWN arrow keys to select a feeder to run.
c. Press

TRIAL PIECE

to feed a piece from the highlighted feeder.

d. Select

Finish

when done.

Adjusting the

Scan Heads

for Picket

Orientation

Marks

(continued)

OTE: The scanning area on your system may appear different, but opera-

tion concepts are the same.

Содержание Relay 5000










































































































































































































Результаты поиска

Содержание Relay 5000

Отзывы:

Pitney Bowes Relay 5000, Руководство оператора, Страница: 175 / 202

Результаты поиска

Содержание Relay 5000

Отзывы: