Pitney Bowes Relay 5000 Скачать руководство пользователя страница 52

Страница: 52 / 202

3-8

SV63136 Rev. A

3 • Basic Operation

3. Slide the tray into the tray mounts until you feel the Tray seat into place.

NOTE:

The tray is seated properly when the notch on the bottom of each

side of the tray is seated in the groove on each of the tray mounts.

4. Pull straight back on the tray slightly, and at the angle at which the Tray

sits, to ensure it is securely attached. If it isn’t, repeat the procedure until

the tray seats properly and securely.

Figure 3.1.2: Check Tray Seating

Figure 3.1.2: Tray Seated Properly in Tray Mount

(bottom view)

Notch on Tray

Groove on

tray mount

Removing Trays

from the Feeder

Tower

The procedure for removing a sheet or insert tray consists of the following:
1. Grasp the open end of the tray and lift up.
2. Slide the tray out until it clears the grooves in the tray mount.

Содержание Relay 5000










































































































































































































Результаты поиска

Содержание Relay 5000

Отзывы:

Pitney Bowes Relay 5000, Руководство оператора, Страница: 52 / 202

Результаты поиска

Содержание Relay 5000

Отзывы: