Pitney Bowes Relay 5000 Скачать руководство пользователя страница 138

Страница: 138 / 202

7-6

SV63136 Rev. A

7 • Add-On Modules

If the sheet width is different from the sheet width used in the previous job,

you need to adjust the HCSF guides for the new job.

IMPORTANT:

Make sure you have enabled the High Capacity Sheet Feeder

Trays before performing this adjustment. Refer to

Enabling and Disabling the High

Capacity Sheet Feeder (HCSF)

Chapter 4

for more information.

1. From the Home screen, select "Loading Instructions", then "Pre-Run

Adjustments", and finally, "HCSF Guide Settings".

2.  Select the Feeder that you will be setting up.
3.  Press TRIAL PIECE.
4.  Open the front and top covers of the enabled HCSF accumulation area.

Adjusting the

HCSF Guides

Figure 7.6: HCSF Front and Top Covers Open

Figure 7.5: HCSF Front and Top Covers

HCSF Top Cover

HCSF Front Cover

Содержание Relay 5000










































































































































































































Результаты поиска

Содержание Relay 5000

Отзывы:

Pitney Bowes Relay 5000, Руководство оператора, Страница: 138 / 202

Результаты поиска

Содержание Relay 5000

Отзывы: