Pitney Bowes Relay 5000 Скачать руководство пользователя страница 172

Страница: 172 / 202

8-26

SV63136 Rev. A

8 • Scanning

3. Fold the sheet horizontally, so the

barcode appears on either side of the

fold line.

4. Open the main transport deck cover.

Use the ruler to measure the distance

from the center of the sheet (lined up

at 0 on the ruler) to the center of the

marks.

5. Refer to the loading instructions to

determine:
• The scan head location to be used

for this sheet (left or right)

• If the sheet will be loaded top or

bottom first.

6. Open the tower cover:

• If the scanner is in the Feeder Tower (Feeders A, B, C, D) open the

feeder tower cover

• If the scanner is in the HCSF (High Capacity Sheet Feeder J, K, L,

M), open the HCSF tower cover.

TIPS:

• Remove the left feeder trays from the feeder tower to allow the HCSF

tower cover to open freely.

•

If you have two HCSFs on your system, the first HCSF Tower will pre

vent the second tower (farthest) from opening fully. For best results,

be sure you have proper lighting when adjusting the scan head in the

second tower.

7. Determine the direction the scan head needs to be moved (to the left or

right of 0 on the ruler):
• Make sure the center of the sheet (the vertical fold) is lined up with

the at the center of the machine (at 0 on the ruler.)

• If the sheet is loaded top first, make sure the arrows point DOWN.
• If the sheet is loaded bottom first, make sure the arrows point UP.

Adjusting the

Scan Heads

for Ladder or

2D Orientation

Marks

(continued)

Horizontal

fold

Содержание Relay 5000










































































































































































































Результаты поиска

Содержание Relay 5000

Отзывы:

Pitney Bowes Relay 5000, Руководство оператора, Страница: 172 / 202

Результаты поиска

Содержание Relay 5000

Отзывы: