Pitney Bowes Relay 5000 Скачать руководство пользователя страница 54

Страница: 54 / 202

3-10

SV63136 Rev. A

3 • Basic Operation

NOTES:

DO NOT pull or push on the side guides to move them. Always use the

side guide adjustor to move the side guides.

Adjusting Tray Side Guides

A grooved, blue side guide adjustor is present at the open end of each tray.

This adjustor controls the opening and closing functions of the tray's side

guides.
To open or close the side guides on sheet and insert trays on the feeder

tower:
1. Place the palm of your hand against the side guide adjustor at the open

end of the tray.

2. Use the palm of your hand to turn the side guide adjustor:

• Turn the adjustor counterclockwise to move the side guides in

towards the material.

• Turn the adjustor clockwise to move the side guides out and away

from the material.

3. When the side guides contact the material in the tray, remove your hand

from the adjustor. The guides will automatically spring back from the

material and leave a space about the thickness of an envelope 1/16-inch

(1.4 mm). This spacing allows for proper material feeding.

Loading Material

into the Trays

(continued)

Side Guide Adjustor

Figure 3.3: Side Guide Adjustor

Содержание Relay 5000










































































































































































































Результаты поиска

Содержание Relay 5000

Отзывы:

Pitney Bowes Relay 5000, Руководство оператора, Страница: 54 / 202

Результаты поиска

Содержание Relay 5000

Отзывы: