Pitney Bowes Relay 5000 Скачать руководство пользователя страница 62

Страница: 62 / 202

3-18

SV63136 Rev. A

3 • Basic Operation

6. Shingle a .7 to 2-inch (20mm to 50mm) stack of envelopes. Place the

envelopes into the HCEF flap side down, flap last.

7. Finish loading a full stack of envelopes (up to 500 pieces), making

sure that the envelopes contact the back of the side guides. It is not

necessary to shingle the remaining envelopes.

NOTES:

• If an HCSF or attached printer is present, you may need to adjust guides

to ensure sheets feed correctly. Refer to

Adjusting the HCSF Guides

Adjusting the Printer Interface Guides

Chapter 7

of this guide for more

information.

• If you are using scanning, you may need to adjust the scan head to ensure

the bar code or OMR mark is read. Refer to

Adjusting the Scan Heads

Chapter 8

of this guide for more information.

3. Place the envelope, bottom edge

first, into the separator so the top

edge (flap crease) lines up with the

edge of the tab on the Wedge.

NOTE:

The edge of the tab is indi-

cated by two arrows.

4. Lower the separator completely, then

push down on the separator gap le-

ver to lock it into place.

5. Pull the envelope out from the HCEF.

Figure 3.8.3: Envelopes Lined Up with Tab on Wedge.

Loading

the HCEF

(continued)

Содержание Relay 5000










































































































































































































Результаты поиска

Содержание Relay 5000

Отзывы:

Pitney Bowes Relay 5000, Руководство оператора, Страница: 62 / 202

Результаты поиска

Содержание Relay 5000

Отзывы: