Pitney Bowes Relay 5000 Скачать руководство пользователя страница 139

Страница: 139 / 202

SV63136 Rev. A

7-7

Add-On Modules • 7

5. Set the Length Guide:

a. Pull the length knob (knob 12) straight out.
b. Turn the knob to position yellow line on the Length Guide Bar at the

trailing end of the sheet.

Adjusting the

HCSF Guides

(continued)

Yellow line on

Length Guide

Bar

Figure 7.7: Length Guide Bar

c. Release the length knob once the Length Guide is properly placed.

6. Set the Width Guides:

a. Turn the right-hand knob on the side of the sheet transport to move

the Width Guides.

b. Move the Width Guides until they just make contact with the sides

of the sheet, then back off slightly (approximately. 1/3 of a turn). The

sheet should lay flat, and not buckle.

7.  Close the front and top covers of the HCSF accumulation area.
8.  Press CLEAR DECK to remove any material in the paper paths.
9.  Repeat steps 3 to 8 to adjust the length and width guides until the sheet

aligns properly.

10. Repeat the entire procedure for each additional HCSF on your system.

Содержание Relay 5000










































































































































































































Результаты поиска

Содержание Relay 5000

Отзывы:

Pitney Bowes Relay 5000, Руководство оператора, Страница: 139 / 202

Результаты поиска

Содержание Relay 5000

Отзывы: