Pitney Bowes Relay 5000 Скачать руководство пользователя страница 59

Страница: 59 / 202

SV63136 Rev. A

3-15

Basic Operation • 3

Adjusting the HCEF Wedge

1. Insert an envelope into the HCEF with the bottom edge of the envelope

against the center guide, in line with the two screws. The top edge of the

envelope (edge with flap) should point towards the wedge.

NOTE:

Ensure the envelope is centered,

not angled

, on the center guide

to obtain correct positioning. If the position of the envelope is incorrect, the

separator gap adjustment will be incorrect as well.

2. Push up and release the blue wedge locking lever.
3. Slide the wedge toward the envelope, until the top edge of the envelope

fits into the center slot of the wedge.

Loading

the HCEF

(continued)

Figure 3.7.1: Adjusting the Wedge Position

Wedge

Locking

Lever

Wedge

Center Guide

Содержание Relay 5000










































































































































































































Результаты поиска

Содержание Relay 5000

Отзывы:

Pitney Bowes Relay 5000, Руководство оператора, Страница: 59 / 202

Результаты поиска

Содержание Relay 5000

Отзывы: