Pitney Bowes Relay 5000 Скачать руководство пользователя страница 110

Страница: 110 / 202

5-14

SV63136 Rev. A

5 • Troubleshooting

Table 5-6 Insertion Area/Envelope Flapper Area Problems,

continued

Problem

Cause

Action

•

Contents of insertion

pack are catching on

side seam inside of

envelope.

•

Contents of insertion

pack are thick and

difficult to insert into

smaller envelopes.

Adjust the Aligner custom settings:

NOTE:

If the contents of the insertion pack are thick, and you

are having trouble inserting the pack into a small envelope, be

sure to set the "Envelope Width" and "Widest Enclosure Width"

to the exact dimensions of the insertion pack.
1.  From the Home screen, select "Menu", then "Jobs".
2.  Select "Edit Current Job", "Edit Job Settings", "Advanced".
3.  Select "Aligner", then "On with Custom Settings". The

Customer Aligner Settings screen displays.

4. Select "Envelope Width". Use the UP/DOWN arrow keys

to increase or decrease the measurement, as necessary.

Select "Accept" when done.

5. Select "Widest Enclosure Width". Use the UP/DOWN

arrow keys to increase or decrease the measurement, as

necessary. Select "Accept" when done.

6. Select "Accept" on the Custom Aligner Settings screen

once the necessary adjustments have been made

Содержание Relay 5000










































































































































































































Результаты поиска

Содержание Relay 5000

Отзывы:

Pitney Bowes Relay 5000, Руководство оператора, Страница: 110 / 202

Результаты поиска

Содержание Relay 5000

Отзывы: