Pitney Bowes Relay 5000 Скачать руководство пользователя страница 58

Страница: 58 / 202

3-14

SV63136 Rev. A

3 • Basic Operation

The HCEF holds up to 500 envelopes. Refer to

Chapter 6, Reference

for the

envelope size ranges.
To load envelopes into the HCEF, you will need to adjust the side guides,

wedge, and separator gap. Before you begin making any adjustments, fan a

stack of envelopes and remove any that are nested, curled, or damaged in

any way.

NOTE:

To view a demo of the wedge (wedge) and separator gap adjustment

processes, go to the Home screen. Select

oading Instructions and Pre-Run

Adjustments

., Use the UP/DOWN arrow keys to select the envelope being fed by

the HCEF, then select

Feeders Setup Demo

Adjusting the HCEF Side Guides

1. Place an envelope between the side guides.
2. Using the adjustor knob, bring the side guides in to lightly touch the

envelope.

3. Release the knob. The guides will spring back to the correct position to

allow free sliding of the envelope between the side guides.

NOTE:

Side guides only spring back after they are moved inward.

4. Make sure the envelope slides freely between the side guides when it is

placed flat on the red feed belts.

Loading the

High Capacity

Envelope Feeder

(HCEF)

Figure 3.6: Adjusting the HCEF Side Guides

Side Guides

Adjustor

Содержание Relay 5000










































































































































































































Результаты поиска

Содержание Relay 5000

Отзывы:

Pitney Bowes Relay 5000, Руководство оператора, Страница: 58 / 202

Результаты поиска

Содержание Relay 5000

Отзывы: