GE MOTOR MANAGER 2 Скачать руководство пользователя | Manualshive

Страница: 195 / 220

background image

GE Power Management

MM2 Motor Manager 2

10-7

10 CONTROL WIRE APPLICATIONS

10.2 HAND/OFF/AUTO CONFIGURATION

10

10.2.5 3 WIRE HAND / 3 WIRE AUTO

This control scheme is used when it is desirable to operate the starter manually and automatically. In
the Hand position, the starter coil is energized via the START button and de-energized via the STOP
button. In the auto position, the starter is energized automatically when the PLC1 contact is pulsed
closed. When the PLC2 contact is pulsed open, the motor stops.

To program the MM2 for three-wire hand / two-wire auto control, set the MM2 to the default settings.

10.2.6 CONTROL OPERATION

HAND:

•

In the hand position, the motor is available to start.

•

When the START button is pressed, the motor runs.

•

When the STOP button is pressed, the motor stops.

OFF:

•

In the off position, the motor will stop.

AUTO:

•

In the auto position, the motor is available to start.

•

When the PLC contact is pulsed closed, the motor runs.

•

When the PLC contact is pulsed open, the motor stops.

•

When the STOP button is pressed, the motor stops.

Terminal 11 (Stop input) must be closed to allow a start. The MM2 display will read “Motor Status
Unavailable” when the stop input is open.

If feedback is not received by the Contactor A Status N.O. input within one second of closing Contac-
tor A output relay, an OPEN CONTROL CIRCUIT alarm will occur. This will cause Contactor A output
relay to open.

«
...
193
194
195
196
197
...
»

Содержание MOTOR MANAGER 2





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MOTOR MANAGER 2

Бренд: Magellan Страницы: 2

GRAVIMETRIC AUGER FEEDER MGF-ST

Бренд: Maguire Products Страницы: 47

Бренд: Magtrol Страницы: 160

Бренд: National Instruments Страницы: 8

Бренд: S&P Страницы: 12

Бренд: S&C Страницы: 34

Бренд: S&C Страницы: 32

IntelliCap Plus

Бренд: S&C Страницы: 32

Бренд: S&P Страницы: 12

Бренд: S&C Страницы: 35

Бренд: Ublox Страницы: 2

Бренд: u-blox Страницы: 19

Бренд: Watts Страницы: 4

Бренд: Yamaha Страницы: 92

Бренд: Viking Страницы: 4

GA Figure 220-D

Бренд: Vag Страницы: 6

Бренд: Zencontrol Страницы: 2

Бренд: Gasboy Страницы: 119

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды