GE MOTOR MANAGER 2 Скачать руководство пользователя | Manualshive

Страница: 155 / 220

background image

GE Power Management

MM2 Motor Manager 2

9-7

9 STARTER TYPES

9.3 TWO SPEED STARTER

9

9.3.2 MM2 SEQUENCES

START LOW SPEED sequence:

1. Start A command received by the MM2 (serial, switch input or faceplate).

2. Close and maintain Contactor A relay – the motor is now in low speed.

START DIRECTLY TO HIGH SPEED (motor stopped,

HIGH SPEED START BLOCK

not enabled)

sequence:

1. Start B command received by the MM2 (serial, switch input or faceplate).

2. Close and maintain Contactor B relay – the motor is now in high speed.

START DIRECTLY TO HIGH SPEED (motor stopped,

HIGH SPEED START BLOCK

enabled) sequence:

1. Start B command received by the MM2 (serial, switch input or faceplate).

2. No response to start B commands.

LOW TO HIGH SPEED TRANSITION sequence:

1. Start B command is received (serial, switch input or faceplate).

2. Open contactor A output relay.

3. Close and maintain Contactor B relay – the motor is now in high speed.

HIGH TO LOW SPEED TRANSITION sequence:

1. Start A command is received (serial, switch input or faceplate).

2. Open contactor B output relay.

3. Wait for the programmed transfer time.

4. Close and maintain contactor A.

STOP/TRIP sequence:

1. Stop command received by the MM2 or a trip occurs.

2. Open the currently closed contactor output relay.

There are many different configurations for the TWO SPEED starter type. Three of the more popular
ones are illustrated here: two-speed one winding constant or variable torque, two-speed one winding
constant horsepower, and two-speed two winding. See the two speed starter diagrams on the follow-
ing pages.

When the power to the MM2 is interrupted, all MM2 output relays de-energize, causing them to open
and stop the motor. The MM2 can only be wired for fail-safe operation.

If feedback is not received from the L or H contacts to the Contactor A or B Status N.O. input within
one second of closing Contactor A relay, an OPEN CONTROL CIRCUIT alarm will occur. This will
cause Contactor A and B output relays to open.

If feedback remains at the Contactor A or B Status N.O. input more than one second after opening
the Contactor A or B output relays, a WELDED CONTACTOR alarm will occur.

«
...
153
154
155
156
157
...
»

Содержание MOTOR MANAGER 2





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MOTOR MANAGER 2

Бренд: Gardena Страницы: 16

Бренд: MADRIX Страницы: 28

Бренд: Daikin Страницы: 2

Бренд: Daikin Страницы: 12

Бренд: Daikin Страницы: 12

Бренд: Daikin Страницы: 46

Бренд: Daikin Страницы: 21

Бренд: Daikin Страницы: 20

Бренд: Jandy Страницы: 28

Бренд: Jands Страницы: 6

Бренд: Daruifuno Страницы: 24

Бренд: D+H Страницы: 2

Бренд: K&K Страницы: 10

MorphoAccess VP MD

Бренд: Idemia Страницы: 29

Бренд: ITALCOPPIE SENSORI Страницы: 2

Бренд: R for Rabbit Страницы: 2

Бренд: LOGICDATA Страницы: 23

Бренд: Zencontrol Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды