GE MOTOR MANAGER 2 Скачать руководство пользователя | Manualshive

Страница: 173 / 220

background image

GE Power Management

MM2 Motor Manager 2

9-25

9 STARTER TYPES

9.8 AUTOTRANSFORMER CLOSED TRANSITION STARTER

9

The

CONTACTOR SEQUENCE

setpoint appears when the Autotransformer Closed Transition starter type

has been selected. The

1S-2S

value means that the 1S contactor will close ahead of the 2S contactor

as per some manufacturers wiring practices. The

2S-1S

value means that the 2S contactor will close

ahead of the 1S contactor as this is another common wiring practice.

The

CHANGE OVER TIME

setpoint appears only if the Autotransformer Open or Closed Transition

starter types have been selected. For the Autotransformer starter type, this is the time delay from the
closure of Contactor A output relay until the opening of Contactor A output relay.

The

STARTS PER HOUR

setpoint only if the Autotransformer starter type has been selected. This set-

point limits the number of starts per hour to prevent overheating of the autotransformer windings.

9.8.2 MM2 SEQUENCES

START (

CONTACTOR SEQUENCE

set to

1S-2S

) sequence:

1. Start command received by the MM2 (serial, switch input or faceplate).

2. Close and maintain Contactor A output relay – close 1S contactor.

3. Wait 20 ms, close and maintain Aux. 1 relay – power is applied to the autotransformer.

4. Wait for the time set in the

CHANGE OVER TIME

setpoint.

5. Open contactor A output relay and wait 20 ms.

6. Close and maintain Contactor B output relay.

7. Wait 20 ms.

8. Open Aux. 1 output relay.

START (

CONTACTOR SEQUENCE

set to

2S-1S

) sequence:

1. Start command received by the MM2 (serial, switch input or faceplate).

2. Close and maintain Aux. 1 output relay – power is applied to the autotransformer.

3. Wait 20 ms, close and maintain Contactor A relay – close the 1S contactor.

4. Wait for the time set in the

CHANGE OVER TIME

setpoint.

5. Open contactor A output relay and wait 20 ms.

6. Close and maintain Contactor B output relay.

7. Wait 20 ms.

8. Open Aux. 1 output relay.

STOP/TRIP sequence:

1. Stop command received by the MM2 or a trip occurs.

2. Open Contactor B output relay.

If feedback is not received by the Contactor A, B or auxiliary relay Status N.O. inputs within one sec-
ond of closing Contactors A, B or the auxiliary output relays, an OPEN CONTROL CIRCUIT alarm
will occur. This will cause Contactors A, B and the auxiliary relay to open.

If feedback remains at any of the Status N.O. inputs for more than one second after opening its
respective relay, a WELDED CONTACTOR alarm will occur.

«
...
171
172
173
174
175
...
»

Содержание MOTOR MANAGER 2





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MOTOR MANAGER 2

FEPL-02 Ethernet POWERLINK

Бренд: ABB Страницы: 2

Бренд: ABB Страницы: 2

ACS850-04 series

Бренд: ABB Страницы: 296

Бренд: ABB Страницы: 320

Бренд: ABB Страницы: 50

Бренд: ABB Страницы: 56

Бренд: Farris Engineering Страницы: 12

Бренд: Eastern Times Technology Страницы: 4

Бренд: Vacon Страницы: 18

Бренд: S-COM Страницы: 400

Бренд: S&P Страницы: 12

Бренд: S&C Страницы: 34

Бренд: S&C Страницы: 32

IntelliCap Plus

Бренд: S&C Страницы: 32

Бренд: S&P Страницы: 12

Бренд: S&C Страницы: 35

PowerFlex 755 IP00

Бренд: Allen-Bradley Страницы: 78

Бренд: Matelec Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды