GE MOTOR MANAGER 2 Скачать руководство пользователя | Manualshive

Страница: 197 / 220

background image

GE Power Management

MM2 Motor Manager 2

10-9

10 CONTROL WIRE APPLICATIONS

10.3 HAND/AUTO CONFIGURATION

10

10.3 HAND/AUTO CONFIGURATION

10.3.1 3-WIRE HAND / 2-WIRE AUTO

This control scheme is used when it is desirable to operate the starter manually and automatically. In
the Hand position the starter coil is energized via the START button and de-energized via the STOP
button. In the auto position the starter is energized automatically by the maintained PLC contact.
When the PLC contact opens, the motor stops.

To program the MM2 for three-wire hand / two-wire auto control (hand/auto configuration), set:

S3 PROCESS\PROGRAMMABLE INPUTS\INTERLOCK INPUT 1:

TWO WIRE CONTROL

S3 PROCESS\PROGRAMMABLE INPUTS\INTERLOCK INPUT 2:

AUTO PERMISSIVE

S3 PROCESS\PROGRAMMABLE INPUTS\INTERLOCK INPUT 3:

AUTO START A

S3 PROCESS\STOP CONFIGURATION\FACEPLATE STOP:

LATCHED

S3 PROCESS\STOP CONFIGURATION\PROCESS STOP:

LATCHED

The

INTERLOCK INPUT 1/2/3

setpoints were chosen to match the wiring diagram provided.

Any of the available Interlocks 1 through 10 could be programmed for

TWO WIRE CONTROL,

AUTO-PERMISSIVE,

or

AUTO START A

c) CONTROL OPERATION

HAND:

•

In the hand position, the motor is available to start.

•

When the START button is pressed, the motor runs.

•

When the STOP button is pressed, the motor stops and a latched trip is generated. The motor
cannot be restarted until reset is pressed.

•

When the faceplate stop key is pressed, it causes a latched trip. The motor cannot be restarted
until reset is pressed.

AUTO:

•

In the auto position, the motor is available to start.

•

When the PLC contact closes, the motor runs.

•

When the PLC contact opens, the motor stops and a latched trip is generated. The motor cannot
be restarted until reset is pressed.

•

When the faceplate stop key is pressed, it causes a latched trip. The motor cannot be restarted
until reset is pressed.

•

Start commands from the faceplate, serial port and terminals 12 and 53 are blocked.

Terminal 11 (Stop input) must be closed to allow a start. The MM2 display will read “Motor Status
Unavailable” when the stop input is open.

If feedback is not received by the Contactor A Status N.O. input within 1 second of closing Contactor
A output relay, an OPEN CONTROL CIRCUIT alarm will occur. This will cause Contactor A output
relay to open.

In the case of a faceplate

or process stop trip, the start signal to Terminal 43 should be removed if

restarting is not desired. When the MM2 reset key is pressed, the motor will be restarted based on
terminal 43.

The STOP button at the motor remains active in the auto mode.

NOTE

«
...
195
196
197
198
199
...
»

Содержание MOTOR MANAGER 2





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MOTOR MANAGER 2

Бренд: UNITED Страницы: 22

Бренд: Hafele Страницы: 82

C-NaviGator III

Бренд: C-Nav Страницы: 20

Бренд: Danfoss Страницы: 24

Бренд: Eaton Страницы: 10

Бренд: Idemia Страницы: 29

Pulsafeeder MPC Vector

Бренд: Idex Страницы: 114

Бренд: SYCLOPE electronic Страницы: 40

Бренд: Timotion Страницы: 10

Бренд: Sherlotronics Страницы: 2

Бренд: Rabbit Страницы: 12

Бренд: TCS Страницы: 8

Sundstrom SR307

Бренд: S.E.A. Group Страницы: 5

FLYGT Pareo DCM 711

Бренд: Xylem Страницы: 56

Бренд: DMP Electronics Страницы: 56

Бренд: REMKO Страницы: 20

Бренд: ProMinent Страницы: 2

Sun Blade X6275 M2

Бренд: Sun Oracle Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды