GE MOTOR MANAGER 2 Скачать руководство пользователя | Manualshive

Страница: 59 / 220

background image

GE Power Management

MM2 Motor Manager 2

4-25

4 SETPOINTS

4.4 S3 PROCESS

4

4.4.3 INTERLOCK NAMES

PATH: SETPOINTS

ttt

S3 PROCESS

tt

INTERLOCK NAMES

4.4.4 STOP CONFIGURATION

PATH: SETPOINTS

ttt

S3 PROCESS

ttt

STOP CONFIGURATION

PROCESS INTLK A NAME:

PROCESS INTERLOCK A

Range: 20 alphanumeric characters

The MM2 allows programming of user defined names for the process
interlock functions. To store a name, use the VALUE UP/DOWN keys
to change the cursor to the desired letter or number. Press the
STORE key. This stores the character and moves the cursor to the
next position. Repeat until the entire message has been entered. A
space can be used to replace characters if no new character is
required. If the cursor is at the end of the message, pressing STORE
wraps around to the first position. This message will now appear on
any actual values message relating to process interlock A.

PROCESS INTLK B NAME:

PROCESS INTERLOCK B

Range: 20 alphanumeric characters

See

PROCESS INTERLOCK A NAME

.

↓

↓

PROCESS INTLK J NAME:

PROCESS INTERLOCK J

Range: 20 alphanumeric characters

See

PROCESS INTERLOCK A NAME

.

INTLK COUNTER NAME:

INTERLOCK COUNTER

Range: 20 alphanumeric characters

This setpoint allows defining the name of the interlock counter. See

PROCESS INTERLOCK A NAME

for directions on entering characters.

INTLK COUNTER UNITS:

UNITS

Range: 20 alphanumeric characters

This setpoint allows defining the units of the interlock counter. See

PROCESS INTLK A NAME

for directions on entering characters.

FIELD STOP:

UNLATCHED

Range: LATCHED, UNLATCHED

If the MM2 detects that either Contactor A or Contactor B has dropped
out without receiving a Stop command, an External Stop sequence has
occurred. If the

FIELD STOP

setpoint is set to

UNLATCHED

the message

EXTERNAL STOP

will be displayed. If the

FIELD STOP

setpoint is set to

LATCHED

the MM2 will initiate an Emergency Stop Trip. This trip condi-

tion must be reset before the motor can be restarted.

FACEPLATE STOP:

UNLATCHED

Range: LATCHED, UNLATCHED

When set to

LATCHED

, pressing the STOP button causes a latched trip.

Pressing RESET allows the motor to restart. If the MM2 is receiving a
constant start signal, the motor will start as soon as reset is pressed.

PROCESS STOP:

UNLATCHED

Range: LATCHED, UNLATCHED

When set to latched, a momentary opening of a contact connected to
Terminal 51 will cause a latched trip condition. Pressing the reset key
will allow the motor to restart. If the MM2 is receiving a constant start
signal the motor will start as soon as reset is pressed.

«
...
57
58
59
60
61
...
»

Содержание MOTOR MANAGER 2





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MOTOR MANAGER 2

FEPL-02 Ethernet POWERLINK

Бренд: ABB Страницы: 2

Бренд: ABB Страницы: 2

Бренд: Canon Страницы: 2

Бренд: Aalborg Страницы: 128

Бренд: Hanna Instruments Страницы: 88

Black Force Wireless

Бренд: Hama Страницы: 10

xPico 200 Series

Бренд: Lantronix Страницы: 7

Бренд: Lantronix Страницы: 3

Бренд: Lantronix Страницы: 15

Бренд: Magellan Страницы: 44

Бренд: Namron Страницы: 3

Бренд: National Instruments Страницы: 14

Бренд: National Instruments Страницы: 31

Бренд: National Instruments Страницы: 50

Бренд: National Instruments Страницы: 24

Бренд: National Instruments Страницы: 21

Бренд: National Instruments Страницы: 39

Бренд: National Instruments Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды