GE MOTOR MANAGER 2 Скачать руководство пользователя | Manualshive

Страница: 134 / 220

background image

7-6

MM2 Motor Manager 2

GE Power Management

7.2 FUNCTIONAL TESTS

7 TESTING

7

7.2.5 THERMISTOR INPUT TESTS

Begin testing by storing the following thermistor values:

S1 CONFIGURATION \ THERMISTOR \ HOT RESISTANCE:

30 kOHMS

S1 CONFIGURATION \ THERMISTOR \ COLD RESISTANCE:

0.1 kOHMS

S1 CONFIGURATION \ THERMISTOR \ THERMISTOR ALARM:

ENABLE

S1 CONFIGURATION \ THERMISTOR \ THERMISTOR TRIP:

DISABLE

Place a variable 50 K potentiometer or resistance box across thermistor terminals 17 and 18 as
shown in Figure 7–1: SECONDARY INJECTION TEST SETUP on page 7–2. With the input resis-
tance set to zero, start increasing the resistance until a thermistor alarm occurs. Verify that the Alarm
LED becomes lit and a THERMISTOR ALARM message is displayed. Use an ohmmeter to verify
that the thermistor resistance agrees with the

THERMISTOR HOT

setpoint value.

The thermistor will have to be removed from the MM2 to accurately measure its resistance.
When the resistance has decreased below the

COLD RESISTANCE

setpoint value, the alarm

will disappear.

To check the thermistor trip function, enable the thermistor trip by making the following settings
changes:

S1 CONFIGURATION \ THERMISTOR \ THERMISTOR ALARM:

DISABLE

S1 CONFIGURATION \ THERMISTOR \ THERMISTOR TRIP:

ENABLE

With the thermistor resistance initially set to zero, begin increasing resistance until a thermistor trip
occurs. Note that the Tripped and Stopped LEDs are lit, the contactor A relay has de-energized, the
Running LED is off, and a THERMISTOR TRIP message is displayed. Use an ohmmeter to verify
that the thermistor resistance value agrees with the

THERMISTOR HOT

setpoint value. Decrease the

thermistor resistance below the

THERMISTOR HOT

value but not below the

THERMISTOR COLD

value.

Press the RESET key and verify that the MM2 still indicates a trip. Reduce thermistor resistance
below the

THERMISTOR COLD

value. Press the RESET key again, noting that the Tripped LED turns off

and the default display message returns. Issue a Start A command via the keypad or switch input
and note that Contactor A contacts now close and the Running LED becomes lit.

7.2.6 POWER FAIL TEST

To test the Power Fail circuit, connect the supply voltage to the MM2 through a variac and begin
decreasing control voltage. When the control voltage drops below 80 V for 120 V AC input or 150 V
for 240 V AC input, the fault light comes on and the MM2 ceases to operate. The MM2 has insuffi-
cient voltage to continue accurately monitoring the motor. All output relays will change to their power
off state. Decrease control voltage to zero and then return voltage to its normal operating level. Verify
that the MM2 resumes its normal operation. Check the power fail memory circuit by verifying that set-
points and statistical data have not been altered.

NOTE

«
...
132
133
134
135
136
...
»

Содержание MOTOR MANAGER 2





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MOTOR MANAGER 2

Бренд: Vacon Страницы: 62

Бренд: Saitek Страницы: 44

Бренд: Icom Страницы: 30

Бренд: ICM Controls Страницы: 2

Бренд: ICM Controls Страницы: 2

Бренд: ray Страницы: 11

Бренд: Ublox Страницы: 2

Бренд: u-blox Страницы: 19

Бренд: Dahua Страницы: 137

Бренд: Coccolle Страницы: 11

Бренд: Fox Страницы: 5

Бренд: Greenheck Страницы: 4

Бренд: Vector Страницы: 8

Бренд: FrSky Страницы: 2

Бренд: Objective Imaging Страницы: 11

Бренд: Gardigo Страницы: 12

Бренд: SAFERA Страницы: 32

Бренд: National Instruments Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды