GE MOTOR MANAGER 2 Скачать руководство пользователя | Manualshive

Страница: 60 / 220

background image

4-26

MM2 Motor Manager 2

GE Power Management

4.4 S3 PROCESS

4 SETPOINTS

4

4.4.5 ANALOG INPUT

PATH: SETPOINTS

ttt

S3 PROCESS

tttt

ANALOG INPUT

ANALOG INPUT NAME:

ANALOG INPUT

Range: 20 alphanumeric characters

The MM2 allows the user to program user defined names for the analog
input and units. To store the name, use VALUE UP/DOWN keys to
change cursor to the desired letter or number. Press STORE. This
stores the character and moves the cursor to the next position. Repeat
this sequence until the entire message has been entered. One of the
characters is a blank space which can be used if no new character is
required. If the cursor is at the end of the message, pressing STORE
causes the cursor to wrap around to the first position. This message will
now appear on any actual values message relating to analog input.

ANALOG INPUT UNIT:
UNITS

Range: 20 alphanumeric characters

See

ANALOG INPUT NAME

for details on storing user defined units.

MINIMUM SCALE:

4 mA:

0

Range: 0 to 20000; Step: 10

The analog input can be scaled to user defined values. Minimum (4
mA) and maximum (20 mA) scale values must be specified. Enter the
minimum scale value with this setpoint.

MAXIMUM SCALE:

20 mA: 1000

Range: 10 to 20000; Step: 10

Enter the maximum scale value corresponding to a 20 mA analog input.

ANALOG ALARM LOW

LEVEL:

OFF

Range: 1 to 20000 or OFF; Step: 1

If the analog input scaled value drops below the level set by this set-
point, an Analog Input Low Alarm will occur. Note that the alarm level
must be a value between the

MINIMUM SCALE

and

MAXIMUM SCALE

val-

ues.

ANALOG ALARM LOW

DELAY: 5 s

Range: 1 to 600 seconds or OFF; Step: 1 second

The analog input scaled value must be below the

ANALOG ALARM LOW

LEVEL

for the time specified by this setpoint before an alarm will occur.

ANALOG ALARM HIGH

LEVEL:

OFF

Range: 1 to 20000 or OFF; Step: 1

If the analog input scaled value exceeds the level set by this setpoint,
an Analog Input High Alarm will occur. Note that the alarm level must be
a value between the

MINIMUM SCALE

and

MAXIMUM SCALE

values.

ANALOG ALARM HIGH

DELAY:

5 s

Range: 1 to 600 seconds or OFF; Step: 1 second

The analog input scaled value must be above the

ANALOG ALARM HIGH

LEVEL

for the time specified by this setpoint before an alarm will occur.

ANALOG TRIP LOW

LEVEL: OFF

Range: 1 to 20000 or OFF; Step: 1

If the analog input scaled value drops below the level set by this set-
point, an Analog Input Low Trip will occur. Note that the trip level must
be a value between the

MINIMUM SCALE

and

MAXIMUM SCALE

values.

«
...
58
59
60
61
62
...
»

Содержание MOTOR MANAGER 2





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MOTOR MANAGER 2

Бренд: XBOX Страницы: 2

Бренд: Ickle Bubba Страницы: 23

Бренд: Samsung Страницы: 27

Бренд: ZirbenLüfter Страницы: 36

Elemec3 013-02-0095-002

Бренд: GAI-Tronics Страницы: 12

Бренд: York Страницы: 20

Tissue-Tek TEC 6

Бренд: Sakura Seiki Страницы: 6

Бренд: VAT Страницы: 39

Бренд: Samson Страницы: 124

Бренд: Samson Страницы: 86

Бренд: VAC Страницы: 5

Бренд: Xilinx Страницы: 52

Omnicharge Solar OCS 100-20

Бренд: tbs electronics Страницы: 64

Бренд: GADGETMONSTER Страницы: 30

Бренд: Maximum Controls Страницы: 58

SensoTimer ST6 Duo eco!ogic

Бренд: Kärcher Страницы: 96

Airedale Sentinel

Бренд: Modine Manufacturing Страницы: 2

SAMSUNG URC-4910

Бренд: One for All Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды