GE MOTOR MANAGER 2 Скачать руководство пользователя | Manualshive

Страница: 31 / 220

background image

GE Power Management

MM2 Motor Manager 2

3-5

3 HARDWARE

3.2 KEYPAD

3

3.2.7 START B KEY

FUNCTION: The START B key can be used to start the motor.

EFFECT: Pressing this key will cause the programmed start sequence to begin.

USE: This START B key is used to start a reversing or two speed motor from the faceplate of the
MM2. Start B can also be initiated from the start switch input at the back of the MM2 or from the
serial port.

3.2.8 MESSAGE UP/DOWN KEYS

FUNCTION: The MESSAGE UP and MESSAGE DOWN keys allow the user to move to the next or
previous section of the currently selected page.

EFFECT: Pressing the MESSAGE DOWN key will cause the display to move to the next section of
the current page. Pressing the MESSAGE UP key will cause the display to move to the previous sec-
tion of the current page. Note: If either key is held for more than 1 second, the next or previous sec-
tions will be selected at a fast rate. When the current display is at a page heading, the MESSAGE UP
key has no effect. When the current display is at the end of the page, the MESSAGE DOWN key has
no effect.

USE: These keys are used to move through the sections of the currently selected page.

3.2.9 MESSAGE LEFT/RIGHT KEYS

FUNCTION: The MESSAGE LEFT and MESSAGE RIGHT keys allow the user to scan the next or
previous line of the currently selected section.

EFFECT: Pressing the MESSAGE RIGHT key displays the next line of the current section. Pressing
the MESSAGE LEFT key displays the previous line of the current section. If either key is held for
more than 1 second, the next or previous line will be selected at a faster rate. If the display shows a
section heading, the MESSAGE LEFT key has no effect. If the MESSAGE RIGHT key has no effect,
the display is showing the last line of a section.

USE: These keys are used to move through the lines of the currently selected section.

3.2.10 VALUE UP/DOWN KEYS

FUNCTION: The VALUE UP and VALUE DOWN keys allow the user to change setpoint values prior
to pressing the STORE key.

EFFECT: Pressing the VALUE UP key will increment the currently displayed setpoint value. Pressing
the VALUE DOWN key will decrement the currently displayed setpoint value. If the display shows an
Actual Value these keys will have no effect

USE: These keys can be used any time to change the value displayed in the setpoint messages.

«
...
29
30
31
32
33
...
»

Содержание MOTOR MANAGER 2





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MOTOR MANAGER 2

Бренд: ABB Страницы: 52

Бренд: Lattice Semiconductor Страницы: 30

Бренд: WAFER Страницы: 15

Бренд: Hardi Страницы: 2

Бренд: YASKAWA Страницы: 64

Бренд: V2 Страницы: 3

Бренд: UniKey Страницы: 20

Бренд: Unitech Страницы: 11

Бренд: B meters Страницы: 10

Бренд: Abus Страницы: 12

Бренд: Campbell Страницы: 8

Бренд: Campbell Страницы: 22

Бренд: Fairchild Страницы: 2

Бренд: Fairford Страницы: 233

Бренд: Van Air Страницы: 4

Бренд: Paradox Страницы: 2

Бренд: Fingertips Lab Страницы: 15

Бренд: DSEGenset Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды