GE MOTOR MANAGER 2 Скачать руководство пользователя | Manualshive

Страница: 178 / 220

background image

9-30

MM2 Motor Manager 2

GE Power Management

9.10 WYE-DELTA OPEN TRANSITION STARTER

9 STARTER TYPES

9

9.10.2 MM2 SEQUENCES

START sequence:

1. Start command received by the MM2 (serial, switch input or faceplate).

2. Close Contactor A output relay – the motor is now in a wye configuration.

3. Close Aux. output relay 1M contact.

4. Maintain 1S contactor until

CHANGE OVER CURRENT

or

CHANGE OVER TIME

initiates a transition from

wye to delta. See

CHANGE OVER CURRENT

and

CHANGE OVER TIME

descriptions above for more

detail.

5. Open Contactor A output relay – change over delay 20 ms wye to delta.

6. Close and maintain Contactor B output relay – the motor is now in a delta configuration.

STOP/TRIP sequence:

1. Stop command received by the MM2 or a trip occurs.

2. Open contactor B output relay.

3. Open Aux. output relay 1M contact

When the power to the MM2 is interrupted, all output relays on the MM2 will de-energize causing
them to open and stop the motor. The MM2 can only be wired for fail-safe operation.

If feedback is not received from the Contactor A Status N.O. input within one second of closing Con-
tactor A relay, an OPEN CONTROL CIRCUIT alarm will occur. This will cause All starter output
relays to open. If feedback remains at the Contactor A Status N.O. input more than one second after
opening the Contactor A output relay, a WELDED CONTACTOR alarm will occur.

If feedback is not received from the Contactor B Status N.O. input within one second of closing Con-
tactor B relay, an OPEN CONTROL CIRCUIT alarm will occur. This will cause All starter output
relays to open. If feedback remains at the Contactor B Status N.O. input more than one second after
opening the Contactor B output relay, a WELDED CONTACTOR alarm will occur.

If feedback is not received from the Wye Delta 1M contact interlock input within one second of clos-
ing Contactor A relay, an OPEN CONTROL CIRCUIT alarm will occur. This will cause All starter out-
put relays to open. If feedback remains at the Wye Delta 1M contact interlock input more than one
second after opening the AUX. output relay, a WELDED CONTACTOR alarm will occur.

«
...
176
177
178
179
180
...
»

Содержание MOTOR MANAGER 2





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MOTOR MANAGER 2

Бренд: Badger Basket Страницы: 3

Бренд: UNITED Страницы: 22

Бренд: Hafele Страницы: 82

Бренд: HABONIM Страницы: 9

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 8

Бренд: Hach Страницы: 36

Бренд: Hach Страницы: 72

Бренд: National Instruments Страницы: 8

Бренд: Sanhua Страницы: 3

Бренд: QED Страницы: 26

Бренд: Viking Страницы: 4

GA Figure 220-D

Бренд: Vag Страницы: 6

Бренд: Roger Страницы: 21

Бренд: elsner elektronik Страницы: 148

Бренд: Danfoss Страницы: 4

Бренд: D-M-E Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды