manualshive.com logo in svg

ESI ESI2000, Руководство по эксплуатации

Операционное руководство ESI ESI2000 доступно для свободного скачивания на нашем веб-сайте. Загрузите руководство сейчас, чтобы ознакомиться с деталями по работе с данной моделью. Получите доступ к качественной информации о продукте, чтобы использовать его с максимальной эффективностью.

Поделиться
Скачать
background image

Appendix

237

The following is a list of the default SCSI ID numbers:

ID - 7 (fixed)

Macintosh

ID - 6

Unassigned

ID - 5

ESI (this number can be changed)

ID - 4

Unassigned

ID - 3

Unassigned

ID - 2

Internal Iomega 100MB Zip Drive (if installed)

ID - 1

Unassigned

ID - 0

Internal Macintosh HD (if installed)

Types of SCSI Cables

There are two basic types of SCSI cables in use: DB25 and 50-pin
Centronics. The two types of cable can be identified by their connectors,
which are quite different. When buying SCSI extension cables, it is
important to choose ones with the right type of connectors, since the
two types will not interconnect without a special adapter. The type of
SCSI connectors on the Macintosh are DB25 connectors. These are the
type commonly found on the back of personal computers. The SCSI
connector on the optional SCSI port is the 50-pin Centronics type. Use
only high quality shielded cables that have all the pins connected. Many
cables only have some of the pins wired.

Terminating SCSI Cables

The total length of the SCSI chain should not exceed 15 feet. A general
rule for SCSI cables is: 

The Shorter the Better!

Terminating resistors or terminators are special resistor packs that are
installed on the 

first and last device in the SCSI chain.

 Terminators

are used to reduce line echoes or standing waves on the SCSI bus. An
analogy in an audio system would be impedance matching.

Terminators can either be hidden inside a SCSI device or they can take
the form of termination blocks which can simply be plugged into the
SCSI port.

Terminators apply power to an array of resistors which ensure a full 5
volt swing between high and low levels on the SCSI line. The host
system is required to provide 

Termination Power

. Termination power

has its own wire in the SCSI cable and supplies power to the termination
block. On external hard disk drives, SCSI terminator power is almost
always turned Off and the drives are left un-terminated.

The ESI is shipped with termination power On with the termination
resistors left in place. This assumes that the ESI will be placed at one end
of the SCSI chain. 

The ESI has an automatic system which ONLY

supplies terminator power when it is NOT being supplied by
another device.

 Therefore, you don't need to worry about terminator

power when connecting the ESI.

The more devices you have connected to SCSI and the longer your
cables are, the more it becomes important to have the cables properly
terminated.

!

 

Caution:

 Turn all devices OFF whenever

you change the SCSI cable. Serious damage
to the ESI may result from connecting and
disconnecting SCSI cables with the power
on.

In addition, devices left on when the cable is
unplugged may not respond properly until
powered off and on.

✱

 

Tip:

 Always use 50-pin Centronics-type

cables with the ESI These cables have much
better electrical characteristics and have
fewer problems. Additionally, make sure that
all 50 pins of the cables are actually wired.
Some SCSI cables have only half of the pins
wired.

Содержание ESI2000

















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ESI2000

OMCA 930 Use And Maintenance Manual preview
930
Бренд: OMCA Страницы: 72
Rangevision SPECTRUM Setup preview
SPECTRUM
Бренд: Rangevision Страницы: 28
e+p Elektrik Handels HDT 300 Quick Installation Manual preview
HDT 300
Бренд: e+p Elektrik Handels Страницы: 2
Warehouse-lighting LTR Series Installation Instructions preview
LTR Series
Бренд: Warehouse-lighting Страницы: 3
E2S A112N Installation Instructions preview
A112N
Бренд: E2S Страницы: 5
h/p/cosmos 190/65 3p Original Instruction preview
190/65 3p
Бренд: h/p/cosmos Страницы: 81
Jacto J-1000 Assembly Instructions Manual preview
J-1000
Бренд: Jacto Страницы: 12
Labelmate UCAT-S User Manual preview
UCAT-S
Бренд: Labelmate Страницы: 61
Raven RS1 Guidance And Steering Installation Manual preview
RS1
Бренд: Raven Страницы: 48
Pacific Solana Assembly Instructions Manual preview
Solana
Бренд: Pacific Страницы: 16
Quantum ELM Replacement Instructions Manual preview
ELM
Бренд: Quantum Страницы: 11
Quanser QNET User Manual preview
QNET
Бренд: Quanser Страницы: 21
Quanser 3 DOF Laboratory Manual preview
3 DOF
Бренд: Quanser Страницы: 18
T&D TR-73U User Manual preview
TR-73U
Бренд: T&D Страницы: 28
ValueStore US V16 Quick Manual preview
V16
Бренд: ValueStore US Страницы: 2
Posture Pump Disc Hydrator Instructions preview
Disc Hydrator
Бренд: Posture Pump Страницы: 2
CAB PX Q4.3L Service Manual preview
PX Q4.3L
Бренд: CAB Страницы: 30
U-Line H-8379 Manual preview
H-8379
Бренд: U-Line Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды