ESI ESI2000 Скачать руководство пользователя страница 134 | Manualshive

Страница: 134 / 272

background image

126

ESI Operation Manual

1. Activate Digital Processing module.

2. Select Copy Region (4).

3. Select the sample that you want to copy a section from, then

press ENTER.

COPY REGION from
001 Selected Sample

Select a Sample

4. If the sample is stereo, the following screen will appear. Select

the right side, left side, or both sides (stereo), then press
ENTER.

Otherwise, proceed to the next step.

COPY REGION from
001 Selected Sample
Side: Stereo
Select L/R/Stereo

5. Specify the start point on line two and end point on line three

for the portion of the sample to be copied, then press ENTER.

Use the up and down cursor to choose the appropriate line. The size
of the portion to be copied on line four will change to reflect
changes in the start and end points. Pressing ENTER saves the
selected portion in the clipboard. Copying does not affect the
original sample. The clipboard will retain this data until replaced by
something else to be copied, cut, or backed up.

COPY secs samples
Start: 0.00 00001
End: 1.61 57881
Size: 1.61 57881

«
...
132
133
134
135
136
...
»

Содержание ESI2000

















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ESI2000

Бренд: Parker Страницы: 54

Бренд: Obdstar Страницы: 10

Бренд: YATEK Страницы: 72

Бренд: Bard Страницы: 144

Бренд: GALBIATI Страницы: 8

Бренд: Vahva Jussi Страницы: 9

Бренд: Water Witch Страницы: 2

Бренд: Falltech Страницы: 48

Бренд: ICP DAS USA Страницы: 45

Lab companion SI-300

Бренд: Jeio tech Страницы: 69

IP Video Test Option HST-3000

Бренд: JDS Uniphase Страницы: 4

Бренд: Jct Страницы: 16

Бренд: Raytheon Страницы: 68

Бренд: KegLand Страницы: 23

Бренд: PASCO Страницы: 5

Бренд: Pasco Scientific Страницы: 27

Бренд: PARUS Страницы: 6

Бренд: R&S Страницы: 371

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды