ESI ESI2000 Скачать руководство пользователя страница 178 | Manualshive

Страница: 178 / 272

background image

170

ESI Operation Manual

Sample 1

Sample 2

Sample 3

ZONE

Sample 4

If you just want to select the existing zone, simply press ENTER when
the display asks you for the high key. The entire zone will be selected.

The second line shows the note being played on the keyboard (or
scrolled with the Data Entry Control). After selecting a note, the third
line displays the primary sample number, and the fourth line displays
the secondary sample number associated with the note on line two.

EDIT ASSIGNMENT
Zone: C1 to C2
Original Key: G1
Edit Low Key

6. Edit the assignment, then press ENTER.

The display shows the

zone range (typically the low and high notes of a particular sample)
and the original key. Use the cursor buttons to select parameter(s) to
edit, and select keys by using the keyboard or Data Entry Control.

In this screen you set the new zone assignment.

If you extend the

new zone so that it overlaps another sample on the same layer, it will
replace the other sample in that area of the keyboard. After pressing
ENTER the ESI will edit the zone range and the original key, and
then return to the Module Identifier.

APPLICATION:

Adjust the range of a sample.

1. Activate Preset Definition module.

2. Select Edit Assignment (2).

3. Select the proper layer, then press ENTER.

If there are only

primary or secondary samples, the ESI automatically goes to step
four.

4. Select the lowest note of the desired zone using the

Data Entry

Control

, then press ENTER.

The Data Entry Control scrolls

through the lowest note of each sample on the keyboard.

5. When the display asks for the highest note of the zone,

simply press ENTER.

6. Edit the zone's range.

Do not change the original key. (It need

not be within the range of the zone.) If you are extending the
range of a sample, the other samples will move to make room for
the new zone.

New Zone Range

New Original Key

«
...
176
177
178
179
180
...
»

Содержание ESI2000

















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ESI2000

Бренд: Taber Страницы: 27

Бренд: Barreto Страницы: 20

Бренд: Barreto Страницы: 18

Бренд: Backyard Discovery Страницы: 41

Бренд: Tabi Страницы: 8

Бренд: Dabi Atlante Страницы: 102

Бренд: Datex-Ohmeda Страницы: 80

Бренд: MacDon Страницы: 2

Бренд: V-TAC Страницы: 6

Бренд: Gatekeeper Страницы: 8

Bure Rise & Go DB 56-309

Бренд: Gate Страницы: 8

Бренд: Kärcher Страницы: 88

Бренд: YMC Страницы: 49

Бренд: Octane Fitness Страницы: 8

Бренд: Octane Fitness Страницы: 10

Бренд: OCENCO Страницы: 48

Бренд: Ocean Optics Страницы: 6

Бренд: Labnet Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды