ESI ESI2000 Скачать руководство пользователя страница 183 | Manualshive

Страница: 183 / 272

ESI ESI2000 Скачать руководство пользователя страница 183

Preset Definition

175

8. If you selected only primary or secondary samples, select

whether you want to load them into the preset as primary or
secondary samples.

This step allows you to copy primary sample(s)

into secondary locations and visa versa. If in step four you selected
both samples, the ESI will skip this step, as these samples are always
copied into both primary and secondary sample slots of the destina-
tion preset.

COPY ZONE from
P01 pri

Select pri/sec

9. Select the low key where the low key of the zone will be placed,

then press ENTER.

As you select notes, the display will show the

samples mapped into the preset. After loading, the ESI will return to
the Module Identifier.

LOAD ZONE into
P01 both C1

Select New Low Key

!

Caution:

When a zone is copied, it

overwrites that area of the destination preset.

«
...
181
182
183
184
185
...
»

Содержание ESI2000

















































































































































































































































































Отзывы:

Нет отзывов