ESI ESI2000 Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 272

background image

Master/Global

71

1. Recalibrate

With this function you can set minimum and maximum values for the
volume control. If you feel that the volume control is not working
correctly, it may be time to recalibrate.

1. Activate Master/Global module.

2. Select Special (8), Volume Recalibrate (1).

3. Move the volume control to the minimum position, then press

ENTER.

VOLUME RECALIBRATE
Min: - 12245

Set Minimum Volume

4. Move the volume control to the maximum position, then press

ENTER again.

VOLUME RECALIBRATE
Min: - 12245
Max: + 13352
Set Maximum Value

5. Check the movement of the control.

Verify that the volume control

operates properly.

Press ENTER.

6. To save the calibration, press Yes.

To cancel the calibration, press

No. In either case, the ESI will return to the Module Identifier.

2. Contrast

This function allows you to change the viewing angle of the LCD so that
it may be easily read from either above or below. The angle is adjustable
from +7 to -8. Positive values make the display easier to read from
above. Negative values make the display easier to read from below.

1. Activate Master/Global module.

2. Select Special (8), Contrast (2).

3. Select the desired contrast setting.

CONTRAST

Contrast: -2
Select Contrast

4. Press ENTER to exit the submodule.

The ESI will return to the

Module Identifier.

«
...
77
78
79
80
81
...
»

Содержание ESI2000

















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ESI2000

Бренд: T-Drill Страницы: 75

Бренд: Zeiss Страницы: 38

Бренд: Cadman Страницы: 66

SATURA SPOT LED PRO

Бренд: Elation Страницы: 41

Бренд: Tapco Страницы: 16

Бренд: Zenbooth Страницы: 40

Visium CytAssist

Бренд: 10x Genomics Страницы: 51

Chromium X Series

Бренд: 10x Genomics Страницы: 5

Бренд: Olsen Страницы: 56

Бренд: Waterous Страницы: 5

Бренд: 3TECH Страницы: 32

Бренд: 4EVAC Страницы: 15

Бренд: A.MENARINI Страницы: 2

Бренд: Rangevision Страницы: 28

Бренд: Eaton Страницы: 21

Бренд: NANO Страницы: 4

BOMAG BW 100 ADM-5

Бренд: Fayat Страницы: 216

Бренд: B medical systems Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды