ESI ESI2000 Скачать руководство пользователя страница 76

Страница: 76 / 272

ESI Operation Manual

•

Automatic Mode:

transfers the complete contents of the source hard

disk (or just the updated banks) to the destination drive without
prompting you at each bank.

•

Interactive Mode:

transfers the banks of the source hard disk drive

to the destination drive, but prompts you to select each source and
destination bank.

4. Select the backup mode and press ENTER.

5. Select the Bank Type.

The display shows:

BACKUP from
D0 Main Drive
D1 Removable Media
Bank Type: All

•

All:

Copies all the banks on your hard disk.

•

Range:

Copies a selected range of disk banks.

6. Select the bank type and press ENTER.

If you selected All or

Updated as the bank type, the screen shown in step 9 will appear.

If you selected Range as the bank type the following screen will appear:

BACKUP Low Range:
D0 Main Drive
D1 Removable Media
13 Baby Burps

7. Select the low bank of the range.

In this menu, you select the

lowest bank in the range of banks which will be copied to the
destination hard disk.

BACKUP High Range:
D0 Main Drive
D1 Removable Media
22 Dog Barks

8. Select the high bank of the range.

9. Press ENTER when the highest bank in the range has been

selected.

The following screen will appear:

Содержание ESI2000

















































































































































































































































































Результаты поиска

Содержание ESI2000

Отзывы:

Похожие инструкции для ESI2000

Бренды по названию

Популярные бренды

ESI ESI2000, Руководство по эксплуатации

Результаты поиска

Содержание ESI2000

Отзывы:

Похожие инструкции для ESI2000

Бренды по названию

Популярные бренды