background image

Digital Processing

151

Path Management Screen

Sound paths may optionally be edited and processed in a number of
ways. 

If the right cursor is pressed in the initial Doppler/Pan screen,

the Path Manager screen appears:

    PATH MANAGER

Path:    user path 1
Function:    reverse

The path may be selected in this screen as well. “Function” specifies the
path processing function. The available functions are:

Edit --------

edit a user path

Copy ------

copy a path into one of the user paths

Reverse --

cause a user path to be played in reverse

Flip --------

flip a user path around the X-axis

Offset -----

apply an x and/or y offset to a user path

Clear ------

initialize a user path

Copy Path

This function copies a pre-programmed or user path to a user path.
When Copy Path is selected, the following screen will appear:

     COPY PATH
From:  medium circle
To  :    user path 1
 Select Source Path

Select the source and destination paths, then press ENTER to copy
the path.

!

 

Note

  The pre-programmed paths must

first be copied to a user location before they
can be edited.

Содержание ESI2000

















































































































































































































































































Отзывы: