ESI ESI2000 Скачать руководство пользователя страница 244 | Manualshive

Страница: 244 / 272

background image

236

ESI Operation Manual

Using SCSI

SCSI (pronounced skuzzy) stands for Small Computer System Interface.
SCSI is an industry standard hardware and software specification that
allows high-speed data transfers between different pieces of equipment.
SCSI devices can include hard disks, tape drives, optical disks and other
types of digital equipment.

Why Use SCSI?

• SCSI is fast! SCSI is a parallel interface which transmits eight bits of

information at a time at high speed over the SCSI cable. MIDI, in
comparison, is a serial interface which can only send one bit of
information at a time over its line.

• Compatibility: Since SCSI is an industry standard, equipment from

many different manufacturers can be linked to work together.

• Expandability: Up to eight SCSI devices can be linked together (the

ESI counts as one SCSI device on the chain).

The SCSI Bus

You may have noticed that the rear panel of most external storage
devices have two SCSI connectors. This is because SCSI devices are
connected together in a chain arrangement. The wires that connect the
different pieces of equipment are called the SCSI bus.

ID Numbers

Each device on the SCSI bus has its own ID number so that it can
distinguish its data from data meant for another device. If data is being
saved to a device with ID-2 for instance, all the other devices on the
SCSI bus will ignore that data. If two devices have the same ID number,
the system will not work. Each device must have its own unique ID
number.

The SCSI ID number of the Macintosh is fixed at ID-7 and cannot be
changed. The SCSI ID numbers of most other devices can be changed.

Many SCSI devices have hardware defined ID numbers, which means
that they have a switch on the front or the back of the unit which allows
the ID number to be easily identified and changed.

!

Caution:

Make sure that no two devices

have the same ID number since this can
corrupt the startup directories of the
Macintosh or the ESI.

✱

Tip:

Use the “Mount Drives” utility

(Master/Global, Disk Utilities, 1) whenever
an external SCSI device does not appear in
the list of available devices.

RM45

ESI

SCSI ID 5

External HD

SCSI ID 3

M.O. Drive

SCSI ID 2

Termination Block is installed

on the Last Device

Termination installed
Internally

I

VOLUME

PHONES

O

TRANSPOSE

DIGITAL PROC

SAMPLE MGT

MASTER/GLOBAL

MULTIMODE

PRESET MGT

DYNAMIC PROC

PRESET DEF

DRIVE SELECT

LOAD

SAVE

AUDITION TRIGGER MODE

ESCAPE

MIDI

ENTER

DEC/NO

INC/YES

1

2

3

4

5

6

7

8

0

9

MIDI CHANNEL: 01
Volume: 115
Pan: -01
000 Synth Flute

(can be changed)

«
...
242
243
244
245
246
...
»

Содержание ESI2000

















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ESI2000

Бренд: T-Drill Страницы: 75

Бренд: Zeiss Страницы: 38

Бренд: Baileigh Industrial Страницы: 40

Бренд: ECE Страницы: 2

Бренд: Ecco Страницы: 5

Evolution Series

Бренд: Bakare Страницы: 38

Бренд: Jaga Страницы: 32

Бренд: M-Audio Страницы: 25

Бренд: Hammer Strength Страницы: 8

Бренд: Crosley Страницы: 6

Бренд: Gambro Страницы: 273

Бренд: Eurotops Страницы: 8

Бренд: KRATOS SAFETY Страницы: 36

Бренд: HYDRA-RIB Страницы: 25

Бренд: Osprey Medical Страницы: 49

Бренд: Richiger Страницы: 76

Бренд: Karma Страницы: 12

Бренд: Blackrock Microsystems Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды