ESI ESI2000 Скачать руководство пользователя страница 116 | Manualshive

Страница: 116 / 272

background image

108

ESI Operation Manual

8. If desired, rename the preset.

Choose the characters to be changed

with the left and right cursor buttons. Select the desired characters
by using the ten key pad, data entry control and keyboard. You can
also use the up cursor to insert spaces and the down cursor to delete
spaces. (See 2. Rename Preset.)

9. Press ENTER to exit the submodule.

The ESI returns to the

Module Identifier.

This submodule allows you to rename any preset in the ESI-32's current
bank.

1. Activate Preset Management module.

2. Select Rename Preset (2).

3. Scroll through the presets available for renaming. When the

display shows the desired preset, press ENTER.

RENAME PRESET

P00 Current Preset
Select a Preset

4. Rename the preset.

Choose the characters to be changed with the

left and right cursor buttons. Select the desired characters by using
the ten key pad, data entry control, and keyboard. You can also use
the up cursor to insert spaces and the down cursor to delete spaces.

RENAME PRESET

P00 Untitled Preset
[0-9]/Encoder/Kybd

5. Press ENTER to exit the submodule.

The ESI returns to the

Module Identifier.

2. Rename

Preset

✱

Tip:

Use the data entry knob or the

increment/decrement buttons to access the
entire character set. A five octave keyboard
does not have enough keys to access all the
available characters.

«
...
114
115
116
117
118
...
»

Содержание ESI2000

















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ESI2000

Бренд: Velocitek Страницы: 81

ABS-Lock X-Flat

Бренд: ABS Страницы: 8

ABS-Lock X-DURCH

Бренд: ABS Страницы: 8

Бренд: ABS Страницы: 8

Бренд: dbx Страницы: 12

Бренд: dbx Страницы: 13

Бренд: dbx Страницы: 72

Бренд: dbx Страницы: 11

Бренд: dbx Страницы: 16

Бренд: TEC Страницы: 6

Бренд: U Technology Страницы: 6

Бренд: ALL-FILL Страницы: 32

ESK+ Manual Knee Lock

Бренд: Blatchford Страницы: 172

Бренд: HEINE OPTOTECHNIK Страницы: 52

Бренд: Ugin Страницы: 39

AURO SPOT CLAS100

Бренд: Cameo Страницы: 60

Бренд: SDE Lighting Страницы: 7

Бренд: Southern States Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды