manualshive.com logo in svg

ESI ESI2000, Руководство по эксплуатации, Страница: 209 / 272

Поделиться
Скачать
ESI ESI2000 Скачать руководство пользователя страница 209

Dynamic Processing

201

With 0.00 tracking, a sample’s timbre remains constant over the
selected zone. This generally gives the most realistic synthesizer and
instrument sounds. With positive tracking, the sample’s timbre
becomes brighter as you play higher up in the zone.

•

Envelope Amt:

 varies the effect of the filter envelope on the filter

cutoff frequency from -100, which is the maximum inverted
envelope, t00, which has no effect from the envelope, to
+100, which is the maximum positive envelope. It is usually
necessary to raise the filter cutoff value when using inverted
envelopes.

Initial

Cutoff

Freq.

+

-

ZONE

Keyboard Tracking varies the filter cutoff frequency as you play up and down the keyboard.

Higher

Filter

Cutoff

Lower

Filter

Cutoff

+100 (

Max. Positive Envelope)

-100 (

Max. Negative Envelope)

Initial Cutoff Freq.

The filter cutoff frequency can be modulated with a positive or negative envelope amount.

5. Select page three by pressing the right cursor button. 

The third

page displays the following parameters for the VCF AHDSR enve-
lope generator:

 VCF Attack:   0.00s
Hold:          0.00s
Decay:         0.00s
Sus:100%  Rel: 1.04s

Содержание ESI2000

















































































































































































































































































Отзывы:

Нет отзывов