ESI ESI2000 Скачать руководство пользователя страница 115

Страница: 115 / 272

Preset Management

107

1. Load

Preset

A preset, with its samples, can be loaded from the floppy disk, the
internal Zip disk or an external storage device.

1. Activate Preset Management module.

2. Select Submodule Load Preset (1).

3. If you wish to select a different drive, move the cursor to the

drive number.

If not, go to step 5.

4. Select the drive containing the preset to be loaded, then press

ENTER.

LOAD PRESET from
D1 Main HD

Select a Drive

5. Select the bank number that contains the preset to be loaded,

then press ENTER.

LOAD PRESET from
D1 Main HD
B00 Current Bank
Select a Bank

6. Select the preset to be loaded, then press ENTER.

LOAD PRESET from
P00 Current Preset

Select Source Preset

7. Select the destination preset number into which the source

preset will be loaded, then press ENTER.

If you try to overwrite

an existing preset, you will be asked if you are sure. Enter Yes to
replace the existing sample, or No to cancel the operation.

LOAD PRESET into
P00 Selected Preset
P00 Empty Preset
Select Dest Preset

✱

Tip:

If you load a preset that uses

samples already present in the bank, new
copies of the samples will not be loaded.
This technique saves a great deal of memory
space. However, the samples must be
identical, even down to the name, otherwise
new samples will be loaded.

The Rename Preset screen appears on the display.

Содержание ESI2000

















































































































































































































































































Результаты поиска

Содержание ESI2000

Отзывы:

Похожие инструкции для ESI2000

Бренды по названию

Популярные бренды

ESI ESI2000, Руководство по эксплуатации

Результаты поиска

Содержание ESI2000

Отзывы:

Похожие инструкции для ESI2000

Бренды по названию

Популярные бренды