ESI ESI2000 Скачать руководство пользователя страница 228 | Manualshive

Страница: 228 / 272

background image

220

ESI Operation Manual

MASTER EFFECT A
Decay Time: 40
HF Damping: 64
FxB==>FxA: 0

11. Press the Right Cursor key

again to go to the Effect Sends

screen.

Set the effect sends amounts

to your preference.

MASTER EFFECT A
Sends:
Main: 20% Sub2: 0%
Sub1: 0% Sub3: 0%

12. Press Enter

to save the system.

If you want to adjust the Effect B settings, press the Escape key to go
back to the main Effects screen. Select Master Effect B (1) and adjust
just as you did for the “A” effect.

Using Master Effects Settings in Multi Mode

In Multi Mode, the two effects processors can be controlled from the
Master Effects settings, or they can follow the effects settings of the
preset on a special MIDI channel. In this example, the Master Effects will
be used. Use this setting if you don't need to change the effects during
the song.

þ

To Use the Master Settings in Multimode

1. Press the Master/Global key

. The Master/Global menu appears.

2. Select Effects (4)

. The main Effect screen will appear.

3. Select Effects Setup (2)

. The following screen will appear.

EFFECT SETUP
Effects: Enabled
Multimode Control:
master settings

4. Select “master settings”

from the “Multimode Control” field. This

causes the Master effects settings to be used.

5. Press Enter

to lock in the change.

6. Select Effects (4)

again to adjust the Master Effects. The main

Effect screen will appear.

7. Select Master Effect A

(0). The following screen will appear.

?

Note:

Effect parameters are described

later in the appendix beginning on page 231

«
...
226
227
228
229
230
...
»

Содержание ESI2000

















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ESI2000

Бренд: Rath Страницы: 3

Бренд: Cameo Страницы: 64

Бренд: Cameo Страницы: 100

Бренд: CAME Страницы: 32

Бренд: NCR Страницы: 20

Бренд: DARAY Страницы: 32

Body Armor Night Splint

Бренд: Darco Страницы: 2

Бренд: MacDon Страницы: 74

Бренд: EAW Страницы: 2

Бренд: abc Страницы: 28

Бренд: Ecler Страницы: 108

Бренд: R&S Страницы: 121

Бренд: Water Witch Страницы: 2

Бренд: Falltech Страницы: 48

Бренд: Fenton Страницы: 16

Бренд: RBC Bioscience Страницы: 24

Бренд: S&C Страницы: 16

Бренд: S&C Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды