manualshive.com logo in svg

ESI ESI2000, Руководство по эксплуатации, Страница: 247 / 272

Поделиться
Скачать
ESI ESI2000 Скачать руководство пользователя страница 247

Appendix

239

Using Multiple Samplers on the SCSI Bus

ESI version 2.0 software adds arbitration to the SCSI protocol so that
multiple “Master” devices can share the bus without a system crash. Two
ESI's (an EIIIX, an e-64, or an E-IV) can share the same sound library,
without having to duplicate the storage media.

When connecting your system for use with multiple ESI's, be sure to
observe the following rules:

•

NEVER try to write to two devices at the same time or write to
one device while loading from another. 

Designate one unit as the

Master which is the 

ONLY

 unit allowed to write. Turn Undo Off on

all units except the Master. Simultaneous reads are OK.

• Keep SCSI cable lengths as short as possible (Under 12 feet total).
• Make sure that each SCSI device has its own unique ID number.

(Remember that the ESI and EIIIX each use up an ID number in
addition to their internal hard disks.)

• Make sure the system is correctly terminated - The ESI's should

normally be on the ends of the SCSI chain.

SCSI Problems

In diagnosing SCSI problems the first rule is: Don't panic, 

Experiment!

If you have several SCSI devices hooked up, try disconnecting one of the
devices and maybe change the order of the units on the line. The follow-
ing checklist may help you find the solution to your unique SCSI setup.

1. Make sure the drive is mounted.

 Mount the drives using the

Mount Drive utility (Master/Global, Disk Utilities, 1).

2. Check the SCSI ID numbers.

 No two numbers can be the same.

3. Read the documentation again.

 Learn all you can about your

peripheral devices. The answer may be right in front of you.

4. Play with the order in which devices are powered up

. Nor-

mally the “Big Bang” method works best (turn everything on at
once), but another order may work better in your unique system.

5. Always suspect the cable when something doesn't work on
the SCSI bus.

 Remember: The shorter the cables are, the better.

6. Simplify the situation.

 Disconnect one or more drives until you

get the system to work.

7. Are the ends of the SCSI bus terminated?

8. If all else fails, call us

 at 408-438-1921. Telephone support

hours are 9:00 to 5:00 PST, Monday through Friday.

!

 

Caution:

 Use the 

Install File System

option #8  (see Master, Format) when
formatting 

Iomega Zip

 drive cartridges.

The normal format procedure will not work
and corrupts the disk.

SCSI ID 5 

External HD

ESI

SCSI ID 4 

ESI

I

VOLUME

PHONES

O

TRANSPOSE

DIGITAL PROC

SAMPLE MGT

MASTER/GLOBAL

MULTIMODE

PRESET MGT

DYNAMIC PROC

PRESET DEF

DRIVE SELECT

LOAD

SAVE

AUDITION TRIGGER MODE

ESCAPE

MIDI

ENTER

DEC/NO

INC/YES

1

2

3

4

5

6

7

8

0

9

MIDI CHANNEL:       01
Volume:              115
Pan:                    -01
000 Synth Flute

I

VOLUME

PHONES

O

TRANSPOSE

DIGITAL PROC

SAMPLE MGT

MASTER/GLOBAL

MULTIMODE

PRESET MGT

DYNAMIC PROC

PRESET DEF

DRIVE SELECT

LOAD

SAVE

AUDITION TRIGGER MODE

ESCAPE

MIDI

ENTER

DEC/NO

INC/YES

1

2

3

4

5

6

7

8

0

9

MIDI CHANNEL:       01
Volume:              115
Pan:                    -01
000 Synth Flute

Internal SCSI ID

TERMINATED

UNTERMINATED

TERMINATED

SCSI ID 6 

Internal SCSI ID

Содержание ESI2000

















































































































































































































































































Отзывы:

Нет отзывов