manualshive.com logo in svg

ESI ESI2000, Руководство по эксплуатации, Страница: 158 / 272

Поделиться
Скачать
ESI ESI2000 Скачать руководство пользователя страница 158

150

ESI Operation Manual

5. Set the amplitude Threshold

. Certain sound paths may take the

sound source very far away from the listener, resulting in little or no
resulting amplitude. The “Threshold” parameter specifies the maxi-
mum amplitude attenuation of the original sample that will ever
occur. By setting this parameter appropriately, you can ensure that
the resulting sample will produce at least a minimum amplitude
output at every point along the path. A setting of 0 dB would
prevent any amplitude changes whatsoever. A setting of -96dB
would not prevent the sound from completely fading away at some
points.

6. Press ENTER to continue. 

The Path Parameters screen (shown

below) will appear.

   PATH PARAMETERS

Duration:      3.06s
Auto-repeat:     off

7. Select a shorter Path Duration if desired. 

The Path Duration

allows you to scale the path time so that it runs to completion in a
time shorter than the length of the sample. The default value is
always the length of the sample. If auto-repeat is off (see below), the
sound will remain at the end of the path until the sample is com-
plete.

8. Turn Auto-repeat On or Off as desired. 

Auto-repeat causes the

path to repeat if the end is reached before the sample has completely
played. Auto-repeat will only occur if path duration is set to a value
less than the sample length. The default setting for Auto-repeat is
Off.

9. Press ENTER to begin processing the sample.

 The display shows:

    DOPPLER/PAN

Processing path...

10. If you are not satisfied with the resulting Doppler/Pan or want

to compare before and after, use Digital Processing, Undo (9).

✱

 

Tip:

 Pressing the right cursor button

from the initial screen selects the Path
Management screen described on the
following page.

Содержание ESI2000

















































































































































































































































































Отзывы:

Нет отзывов