ESI ESI2000 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 272

background image

Master/Global

61

0. SCSI Setup

This utility allows you to change the SCSI ID number of the ESI itself
(not a connected hard disk) in the event that it conflicts with a device on
the SCSI bus having the same ID number.

The SCSI interface, located as a 50-pin connector on the back panel,
allows the ESI to communicate with external storage devices. The ESI
can support seven SCSI devices (including its internal HD if it has one).
Each device on the SCSI bus has its own ID number so that it can
distinguish its data from data meant for other SCSI devices. If a SCSI
device is added to your system which has the same ID number as an
existing device, a SCSI error would occur. To remedy this situation, the
ID number on the new device will have to be changed. Consult the
operation manual of the external device for information on changing the
SCSI ID number.

The ESI also contains special SCSI software that allows two “master”
devices (the ESI and a Macintosh, for example) to coexist on the SCSI
bus. If you have a computer connected to the ESI SCSI bus, the “Ignore
Host on ID” function should be set to the ID number of the computer so
the ESI will not try to access the computer itself as one of its disk drives.

1. Activate Master/Global module.

2. Select Disk Utilities (7), SCSI Setup (0).

3. Select the new SCSI ID number.

SCSI SETUP

ESI SCSI ID: 5
Avoid Host on ID: 7

4. If a computer is present on the SCSI bus set “Avoid Host on ID”

to the computers SCSI ID number.

If a computer is not present on

the SCSI bus, this function should be turned Off.

5. Press ENTER to exit the submodule.

The ESI saves your choices

to the System and returns to the Module Identifier.

✱

Tip:

The ID number of a Macintosh

computer is set at 7.

«
...
67
68
69
70
71
...
»

Содержание ESI2000

















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ESI2000

Бренд: Olympus Страницы: 86

Бренд: ACCU-CHECK Страницы: 104

Martin ERA 800 Performance

Бренд: Harman Страницы: 32

Martin ERA 600 Performance

Бренд: Harman Страницы: 32

Бренд: Sabre Страницы: 2

Бренд: Keithley Страницы: 79

Бренд: Kayakpro Страницы: 17

Бренд: Yoshitake Страницы: 11

Contrology Cadillac

Бренд: Balanced Body Страницы: 7

Бренд: M-Audio Страницы: 3

Бренд: Xtralis Страницы: 26

Бренд: rbd instruments Страницы: 18

Бренд: Össur Страницы: 50

Бренд: Össur Страницы: 13

PRO-FLEX XC PXC0xyyz

Бренд: Össur Страницы: 68

Бренд: Össur Страницы: 25

Бренд: Össur Страницы: 2

Бренд: Össur Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды