manualshive.com logo in svg

ESI ESI2000, Руководство по эксплуатации, Страница: 162 / 272

Поделиться
Скачать
ESI ESI2000 Скачать руководство пользователя страница 162

154

ESI Operation Manual

X-Y coordinates are specified in 10ths of feet. X values range from -999
(-99.9 feet) to +999 (99.9 feet), Y values from 0 to 999 (99.9 feet). The
listener is considered to be at [0,0] as shown below:

The first part of the coordinate designates the left/right position. The second part of the coordinate
designates the forward positioning.

Time values range from 0 to the length of the current sample. Note that
if this path is applied to a different sample, all time values will be scaled
to the length of the different sample.

The diagram above shows the extreme positions of the path coordinates.

Once path editing is complete, press ENTER to return to the Path
Management screen. When the path is ready to apply to the sample,
press the left cursor button while in the Path Management screen to
return to the main Doppler/Pan screen. Press ENTER again to move
ahead to the Path Parameters screen and once more to process the
sample.

X

X

R

Forward

L

Y

±999, 999

Y

0,0

-999, 0

0, 0

+999, 0

-999, 999

+999, 999

X

Y

X

Y

X

Y

X

Y

X

Y

0, 999

R

Forward

L

Содержание ESI2000

















































































































































































































































































Отзывы:

Нет отзывов