ESI ESI2000 Скачать руководство пользователя страница 143 | Manualshive

Страница: 143 / 272

background image

Digital Processing

135

3. Reverse Section

Reverses all or part of a sample.

1. Activate Digital Processing module.

2. Select Digital Tools I (7), Reverse Section (3).

3. If the current sample is stereo, the following screen appears.

Select the left side, right side, or both sides (stereo), then press
ENTER.

Otherwise, proceed to the next step.

REVERSE SECTION

Side: Stereo
Select L/R/Stereo

4. Select the desired section of the sample to be reversed and press

ENTER.

REVERSE secs samples
Start: 0.00 000000
End: 3.13 137873
Size: 3.13 137873

The display shows the current points at which the sound will be re-
versed, which will be the endpoints of the current sample. The sample
will be reversed between the selected start and end points.

5. If you are not satisfied with the reversal, or want to compare

before and after, proceed to Digital Processing, Undo (9).

4. Stereo <-> Mono

Converts a stereo sample to mono or a mono sample to stereo. Mono
samples are created using the left side of a stereo sample. Stereo samples
are created by simply duplicating the mono sample on the other side.

1. Activate Digital Processing module.

2. Select Digital Tools I (7), Stereo <-> Mono (4).

The display asks

if you want to convert the current sample to stereo (if it is mono) or
to mono (if it is stereo).

STEREO <-> MONO

Convert to Mono?

✱

Tip:

The left and right cursor keys will

change the start and end points so that they
fall on positive zero-crossing points in the
waveform.

«
...
141
142
143
144
145
...
»

Содержание ESI2000

















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ESI2000

Бренд: BACtrack Страницы: 13

Бренд: Badgematic Страницы: 28

Бренд: BACtrack Страницы: 2

Бренд: MADRIX Страницы: 28

Бренд: BACTcontrol Страницы: 28

Бренд: Datalogic Страницы: 48

Бренд: PageFlip Страницы: 32

Бренд: Panta Safe Light Страницы: 2

Бренд: Calrec Страницы: 70

bionic power knee

Бренд: Össur Страницы: 2

BALANCE KNEE OM8

Бренд: Össur Страницы: 36

Бренд: Össur Страницы: 37

REBOUND DIABETIC WALKER

Бренд: Össur Страницы: 63

Бренд: Össur Страницы: 67

ECHODIA Babyscreen

Бренд: Électronique du Mazet Страницы: 65

Бренд: Kattsafe Страницы: 19

Serious Steel 805106

Бренд: ParaBody Страницы: 6

Z33-D060.02 S2A

Бренд: Jäger Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды