ESI ESI2000 Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 272

background image

84

ESI Operation Manual

An Akai SCSI device is NOT mounted and accessed like a normal ESI
drive (the load and drive buttons will not access the Akai drive). Instead,
it is accessed and operated using the Akai menus. Only one Akai SCSI
device can be known to the ESI at any given time.

4. Press 0 on the keypad to select Akai SCSI Setup.

This step is

necessary for the ESI to recognize the Akai SCSI device. The display
shows:

AKAI SCSI SETUP
SCSI drive ID:search
TOSHIBA CD-ROM DRIVE
Select search or ID

The setup screen is used to select the SCSI ID of the attached Akai SCSI
device. The SCSI ID may be selected by using the INC/DEC buttons, or
by typing the digit (1-7) directly using the ESI keypad. The default
choice, “Search,” instructs the ESI to search for the first Akai device in
the SCSI chain. Normally you will use “Search” unless you want to select
a specific Akai device out of several on the SCSI bus. Press ENTER, to
confirm your choice and return to the option select screen.

•

WARNING:

If you have an Akai S1000 or S1100 connected to the

SCSI bus, you MUST enter the SCSI ID number of the Sampler (not
the HD) manually. Failure to do so will cause the system to crash.
Press the right cursor button for the next screen, then select the ID
number of the S1000 or S1100. This ID number is remembered on
power down.

5. Press 1 to select the Import Options screen.

The following screen

will appear. Press ENTER when you have selected your choices.

AKAI IMPORT OPTIONS
Adjust loops: on
Full placement: on
Combine -L/-R: off

Adjust Loops

Sample looping is implemented differently on the ESI and the Akai.
Because of this difference, certain sample loops may “tick” slightly or
appear out of tune after being transferred from the Akai. This function
will automatically repair any incorrect sample loops immediately after
the samples are transferred. Be advised that the transfer may take slightly
longer (up to 15% more time) with Adjust Loops turned On.

!

Caution:

Drive 0 cannot be used since

the ESI uses this number for the floppy disk.

«
...
90
91
92
93
94
...
»

Содержание ESI2000

















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ESI2000

Бренд: ABB Страницы: 6

Бренд: ZOLL Страницы: 344

Бренд: ABB Страницы: 9

Giraffe OmniBed

Бренд: Ohmeda Страницы: 54

Бренд: GE Страницы: 802

Бренд: iET Страницы: 17

Бренд: MacDon Страницы: 84

Бренд: MacDon Страницы: 89

Бренд: Patton electronics Страницы: 18

Бренд: FEAS Страницы: 72

Бренд: PANDROL Страницы: 36

Бренд: Ibiza Страницы: 21

Бренд: IBC Страницы: 8

Бренд: Ibanez Страницы: 8

Бренд: IAI Страницы: 5

Бренд: Rapala Страницы: 14

Бренд: S.R.Smith Страницы: 43

Бренд: MacDon Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды