Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 2

Страница: 2 / 128

Operating Instructions

Single-pole Conductor Rail System

SingleFlexLine Program 0815

BAL0815-0002g-US
www.conductix.us

translated document

page 2 of 128

Contents

General Information .................................................................................................................................................................... 5

1.1

About this document .................................................................................................................................................... 5

1.2

Limitation of liability ..................................................................................................................................................... 5

1.3

Copyright ..................................................................................................................................................................... 6

1.4

Replacement parts ...................................................................................................................................................... 6

1.5

Material defects ........................................................................................................................................................... 6

1.6

Technical support ........................................................................................................................................................ 6

Safety Instructions ...................................................................................................................................................................... 7

2.1

Explanation of symbols ................................................................................................................................................ 7

2.2

Personnel requirements .............................................................................................................................................. 8

2.2.1

Qualifications ............................................................................................................................................................... 8

2.2.2

Unauthorized personnel .............................................................................................................................................. 9

2.2.3

Training ........................................................................................................................................................................ 9

2.3

Personal protective equipment .................................................................................................................................... 9

2.4

Intended use .............................................................................................................................................................. 10

2.5

Unintended use ......................................................................................................................................................... 11

2.6

Protective measures to be taken by the operator/user .............................................................................................. 12

2.7

5 Safety Rules for working on electrical systems ...................................................................................................... 12

2.8

Special hazards ......................................................................................................................................................... 13

2.8.1

Electrical hazards and sources of danger ................................................................................................................. 13

2.8.2

Mechanical hazards and sources of danger .............................................................................................................. 14

2.8.3

Danger due to dust and vapors ................................................................................................................................. 15

2.8.4

Dangers relating to the operating environment ......................................................................................................... 16

2.9

Conduct in the event of accidents and malfunctions ................................................................................................. 17

Technical Data .......................................................................................................................................................................... 18

3.1

Electrical .................................................................................................................................................................... 18

3.2

Mechanical ................................................................................................................................................................ 18

3.2.1

Lengths ...................................................................................................................................................................... 19

3.2.2

Installation orientation ................................................................................................................................................ 19

Содержание SingleFlexLine Program 0815

































































































































Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды