Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 125

Страница: 125 / 128

Operating Instructions

Single-pole Conductor Rail System

SingleFlexLine Program 0815

BAL0815-0002g-US
www.conductix.us

translated document

page 125 of 128

CAUTION!

Risk of injury when removing the connector!

The connector is very large compared to the insulation profile and the conductor bar and e.g., a saw

blade could easily become trapped in it. The saw could also jump and injure the installer.

→

When separating the 4-m rail sections, keep at a distance of at least 100 mm from the end of the

insulation profile.

CAUTION!

Reusing disposable components can create hazards!

Reusing a connector or expanding rivet can create the following hazards:



The connection is not perfect and reliable.



Expanding rivet: There is a risk that conductor rails may come loose, become quickly worn or

destroyed.



Connectors: High-resistance connection, heating, fire hazard reduced performance.

→

Dispose of disassembled connectors and expanding rivets and replace with new ones. Do not re-

use!

11.3

Disposal

DANGER!

Risk of death due to electrical shock!

Contact with components carrying electrical power can lead to death due to electrical shock or se-

vere injury. Risk of injury due to shock reactions, falling or being thrown across the room due to

electrical shock.

→

The main power supply (from the building) must be disconnected in the disassembly area and se-

cured against switching on again.

→

Disconnect all voltage supply line feeds.

→

When decommissioning, check whether a voltage is still present in the components and take

measures where necessary.

In the absence of a return or disposal agreement, disassembled components must be recycled as follows:



All metal parts must be scrapped.



Plastic components must be sent for recycling.



The other components are to be disposed of according to their material composition.

CAUTION!

Environmental damage due to improper disposal!

Electrical waste, electronic components, lubricants and other auxiliary materials are subject to haz-

ardous waste disposal regulations and may only be disposed of by authorized specialists.

Local authorities or special disposal companies can provide information about environmentally appropriate disposal.

Содержание SingleFlexLine Program 0815

































































































































Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды