Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 36

Страница: 36 / 128

Operating Instructions

Single-pole Conductor Rail System

SingleFlexLine Program 0815

BAL0815-0002g-US
www.conductix.us

translated document

page 36 of 128

CAUTION!

Risk of puncture wounds and cuts!

The packaging material can contain sharp objects such as nails, struts, steel bands and wood

splinters that can cause injury to limbs.

→

Wear personal protective equipment!

→

Cordon off the work area!

→

Use caution when working in the vicinity, particularly below the conductor rail.

DANGER!

Risk of injury due to impacts and punctures/stabs from conductor rails sliding out!

Risk of injury due to impacts and punctures/stabs from conductor rails sliding out when the

packaging units are held at an angle, the packaging is damaged or through carelessness

with long loads/transport crates.

→

Wear personal protective equipment!

→

Cordon off the work area!

DANGER!

Risk of death due to electrical shock!

Contact with components carrying electrical power can lead to death due to electrical shock

or severe injury. Risk of injury due to shock reactions, falling or being thrown across the

room due to electrical shock.

→

The main power supply (from the building) must be disconnected in the installation area

and secured against switching on again.

→

Disconnect all voltage supply line feeds.

→

Check whether a voltage is still present in the components and take measures where nec-

essary.

→

Install the conductor rail out of manual reach.

→

Attach a sign stating “Risk of Death due to Electrical Shock” with the relevant hazard sym-

bol in all areas with components under voltage.

→

The customer must provide grounding for metallic components.

→

The customer must provide protective devices.

→

Ensure that there is sufficient stability in the area.

WARNING!

The system must be designed and operated in accordance with the prevailing

ambient conditions!

WARNING!

Secure conductor rails against falling

→

In application areas with personnel traffic and at an installation height of 3 m or more, con-

ductor rails must be secured against falling!

Содержание SingleFlexLine Program 0815

































































































































Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды