Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 102

Страница: 102 / 128

Operating Instructions

Single-pole Conductor Rail System

SingleFlexLine Program 0815

BAL0815-0002g-US
www.conductix.us

translated document

page 102 of 128

Operation

The only operations required to operate the conductor rail system are switching the power supply on and off to stop/activate the
system, see Section 8.2.
The safety information in Section 8.1 must be observed to guarantee safety during operation.

WARNING!

Only operate the conductor rail system in areas inaccessible to the public!

Operation is only permitted in areas inaccessible to the public and out of manual reach.

→

The danger zone must be enclosed by the customer or protection ensured by distance!

8.1

Safety

NOTE!

The system must only be operated by trained personnel!

WARNING!

Danger for unauthorized personnel!

Unauthorized personnel are not familiar with the hazards in the working area.

→

Keep unauthorized personnel out of the working area.

→

In case of doubt, address such persons and direct them away from the working area.

→

Stop work as long as unauthorized persons are in the working area.

Requirement:

DANGER!

Risk of injury due to ensnarement!

There is a risk of being ensnared by moving parts when the system is in operation.

→

Do not enter the danger zones of the system during operation.

In order to comply with the

most important measures

for protection against hazards, the measures specified in Sections 2 and 3

must be observed. For information on foreseeable incorrect applications or unsuitable ambient conditions see Sections 2.5 and 3.3.
in particular.

Содержание SingleFlexLine Program 0815

































































































































Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды