Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 117

Страница: 117 / 128

Operating Instructions

Single-pole Conductor Rail System

SingleFlexLine Program 0815

BAL0815-0002g-US
www.conductix.us

translated document

page 117 of 128

DANGER!

Risk of injury due to cutting and amputation!

Cuts and amputations can occur on:



Sharp edges of the general components



Sharp edges of the conductor rails



Cut edges when trimming the conductor rails



Packaging materials (cartons, bands, etc.)

→

Wear personal protective equipment!

DANGER!

Risk of injury due to ensnarement or impact!

Ensnarement and/or impact with moving conductor rails (slip ring) or current collectors connected to

the machine and other components must be prevented.

→

Cordon off the work area

→

Use caution when working in the vicinity of the danger zone, particularly if protective devices (co-

vers, enclosures, control devices) have been removed or disabled.

→

Wear personal protective equipment!

CAUTION!

Risk of puncture wounds and cuts!

The packaging material can contain sharp objects such as nails, struts, steel bands and wood splin-

ters that can cause injury to limbs.

→

Wear personal protective equipment!

→

Cordon off the work area!

→

Use caution when working in the vicinity, particularly below the conductor rail.

DANGER!

Risk of death due to electrical shock!

Contact with components carrying electrical power can lead to death due to electrical shock or se-

vere injury. Risk of injury due to shock reactions, falling or being thrown across the room due to

electrical shock.

→

The main power supply (from the building) must be disconnected in the installation area and se-

cured against switching on again.

→

Disconnect all voltage supply line feeds.

→

When decommissioning, check whether a voltage is still present in the components and take

measures where necessary.

→

The danger zone must be enclosed by the customer or protection ensured by distance.

→

The customer must provide grounding for metallic components.

→

The customer must provide protective devices.

→

Ensure that there is sufficient stability in the area.

Содержание SingleFlexLine Program 0815

































































































































Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды