Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 15

Страница: 15 / 128

Operating Instructions

Single-pole Conductor Rail System

SingleFlexLine Program 0815

BAL0815-0002g-US
www.conductix.us

translated document

page 15 of 128

2.8.3

Danger due to dust and vapors

WARNING!

Danger of sensitization, irritation of the mucous membranes and respiratory

diseases due to dust and vapors!

Abrasions from the sliding contact carbon brushes collect in the conductor rails

and the guideway. This dust is very fine and is a health hazard. Frequent han-

dling can result in sensitization. Persons who frequently spend longer periods in a

heavily used system without protective equipment must reckon with the following

consequences



Irritations of the mucous membranes



Respiratory diseases



Cancer

These consequences must also be expected if accumulations of dust are handled

without proper care (e.g., removal of dust using compressed air).

→

In workplaces with long-term exposure and heavily trafficked facilities, take ef-

fective measures to protect employees from the dust.

→

During all work on the conductor rail system in which collected dust can be

stirred up, wear personal protective equipment. In particular, wear personal pro-

tective equipment when cleaning the system.



Protective eyewear



Protective dust mask Class FFP3 (observe local regulations)



Protective gloves



Disposable coveralls

→

Before starting work, clean the conductor rail in accordance with regulations.

There are special instructions for this task; see Section 9.

→

Protect the surroundings during cleaning works, for instance by covering or re-

moving warehouse goods and blocking access to those areas in which dust

could fall down on persons.

→

Do not blow out dust with compressed air

; vacuum it up instead. The vac-

uum cleaner must be equipped with a Class H fine filter.

→

Do not eat, drink or smoke during work!

DANGER!

Poisonous vapors/gases in case of fire!

The standard insulation materials contain PVC. Poisonous vapors/gases (HCL) can be pro-

duced during fires.

→

The building must be evacuated immediately.

→

Notify the fire department.

Содержание SingleFlexLine Program 0815

































































































































Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды