Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 31

Страница: 31 / 128

Operating Instructions

Single-pole Conductor Rail System

SingleFlexLine Program 0815

BAL0815-0002g-US
www.conductix.us

translated document

page 31 of 128

Transport, Packaging and Storage

5.1

Safety

Required protective equipment:

WARNING!

Risk of death due to suspended loads!

Falling parts or uncontrolled swinging loads can lead to severe injury or even death.

→

Never walk under suspended loads.

→

Only use the attachment points provided; do not fasten lifting accessories to projecting ma-

chine parts or to eyelets on components.

→

Be sure the lashing elements are firmly seated.

→

Use only authorized lifting accessories and lashing elements with sufficient load capacity.

→

Do not use torn or damaged ropes or straps; replace them with new ones.

→

Do not attach ropes or straps at sharp corners and edges, and do not knot or twist them.

→

Only move loads under supervision.

→

Set down the load when leaving the workplace.

→

Cordon off the work area.

→

Work carefully when working in the vicinity, particularly below the conductor rail system.

DANGER!

Risk of injury due to crushing skin and limbs!

Skin and limbs can be crushed:



When packing components and handling long loads.



If transport crates are dropped.



With incorrect suspension points for transport crates.



With incorrect and unauthorized loading of transport crates.

→

Wear personal protective equipment!

→

Use suitable lifting gear!

Содержание SingleFlexLine Program 0815

































































































































Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды